ADTRAN MP-114, MP-118 Related Documentation

MP-11x & Microsoft Office Communications Server 2007

Quick Installation Guide 6 Document #: LTRT-26301

Related Documentation

Document # Manual Name

LTRT-656xx (e.g., LTRT-65601 MP-11x & MP-124 SIP Release Notes

LTRT-654xx MP-11x & MP-124 SIP User's Manual

Warning: Ensure that you connect the FXO ports to Central Office (CO) / PBX lines

only.

Warning: The MediaPack is supplied as a sealed unit and must only be installed or

serviced by qualified service personnel.

Warning: Disconnect the MediaPack from the electrical mains and from the Telephone

Network Voltage (TNV) before servicing.

Note: MediaPack and MP-11x refers collectively to the MP-118 and MP-114 FXO

VoIP gateways.

Note: Where “network” appears in this manual, it means LAN, WAN, etc. accessed via

the gateway’s Ethernet interface.

Note: FXO (Foreign Exchange Office) is the interface replacing the analog telephone

and connects to a Public Switched Telephone Network (PSTN) line from the

Central Office (CO) or to a Private Branch Exchange (PBX). The FXO is

designed to receive line voltage and ringing current, supplied from the CO or the

PBX (just like an analog telephone). An FXO VoIP gateway interfaces between

the CO/PBX line and the Internet.

Contents

Main Page Table of Contents Page Notices Notice Trademarks WEEE EU Directive Customer Support Abbreviations and Terminology Related Documentation 1 Introduction Page 2 Quick Start 3 Configuring the MediaPack 3.1 Embedded Web Server Management Tool 3.1.1 Accessing the Embedded Web Server To access the Embedded Web Server, take these 4 steps: Page 3.1.3 Changing Login Username and Password To change the user name and password, take these 3 steps: 3.1.4 Searching for ini file Parameters To search for an ini file parameter configurable by the Embedded Web Server, take these 3 steps: 3.2 Assigning an IP Address to the MediaPack 3.2.1 Assigning an IP Address using BootP To assign an IP address using BootP, take these 3 steps: 3.2.2 Assigning an IP Address Using CLI via RS-232 To assign an IP address using CLI via RS-232, take these 5 steps: 3.2.3 Assigning an IP Address using HTTP To assign an IP address to the gateway using HTTP, take these 5 steps: 3.3 Advanced Configuration 3.3.1 Using the ini File 3.3.1.1 Obtaining the ini File from the Web To download the ini file to your PC, take these 4 steps: 3.3.1.2 Uploading the ini File to the Gateway To upload the ini file to the gateway, take these 6 steps: 3.3.1.3 Modifying Parameters Specific to Site Deployment 3.3.2 Using the Embedded Web Server 3.3.2.1 Defining Mediation Server's IP Address To define Mediation Server's IP address, take these 4 steps: 3.3.2.2 Defining Number of FXO Ports Connected to PBX To enable the gateway's FXO ports, take these 4 steps: 3.3.2.3 Defining Voice Coders To define the coder, take these 3 steps: 3.3.2.4 Translating Numbers From / To E.164 Using Manipulation Tables for PBX/PSTN Connectivity To configure the Number Manipulation tables, take these 4 steps: 3.3.2.4.1 Dialing Plan Notation 3.3.2.4.2 Number Normalization Examples Page 3.3.2.5 Defining Answer Supervision To define the Answer Supervision, take these 3 steps: Page 3.3.2.7 Enabling Caller ID To enable Caller ID, take these 3 steps: Page 3.3.2.9 Defining Disconnect on Broken Connection To define Disconnect on Broken Connection, take these 3 steps: 3.3.2.10 Defining DTMF Payload Type To define the DTMF payload type, take these 3 steps: 3.3.2.11 Enabling One-Stage Dialing To enable one-stage dialing, take these 3 steps: 3.3.2.12 Defining Channel Select Mode To define the Channel Select mode, take these 3 steps: 3.3.2.13 Disabling RTCP Attribute To disable the RTCP attribute, take these 5 steps: 4 Backing Up Configuration Settings To save the ini file on your PC, take these 6 steps: 5 Monitoring the Gateway 5.1 Front-Panel LEDs 5.2 Monitoring the Channels To monitor the status of the channels, take this step: To monitor the details of a channel, take these 2 steps: 6 Troubleshooting 6.1 General Troubleshooting 6.2 Restoring Parameters to Factory Default Settings To restore factory default settings, take these 3 steps: 6.3 Debugging using a Syslog Server To configure the Syslog parameters, take these 7 steps: MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 42 Document #: LTRT-26301 7 Regulatory Information Declaration of Conformity Quick Installation Guide 7. Regulatory Information Safety Industry Canada Notice Network Compatibility Telecommunication Safety SELV: Safety extra low voltage circuit.