Manuals / Brands / Computer Equipment / Server / ADTRAN / Computer Equipment / Server

ADTRAN MP-114, MP-118 To download the ini file to your PC, take these 4 steps: , 3.3.1.2 Uploading the ini File to the Gateway , To upload the ini file to the gateway, take these 6 steps:

1 44

Download 44 pages, 1.83 Mb

MP-11x & Microsoft Office Communications Server 2007

Quick Installation Guide 18 Document #: LTRT-26301

Notes:

• Ensure that you download the correct ini file so that your gateway is

configured correctly for interoperability with the deployed PBX / PSTN.

• The gateway configuration for the PBX-Sends-Digits option is similar to the

One-to-Many option. Therefore, for the PBX-Sends-Digits option, download

the ini file for the One-to-Many option.

¾ To download the ini file to your PC, take these 4 steps:

1. Open your Web browser, and then in the URL address field, enter the following address:

http://www.audiocodes.com/Content.aspx?voip=2823; the 'Microsoft Office Communications

Server 2007 Resource Page' page opens, as shown below:

Figure 3-7: Microsoft Office Communications Server 2007 Resource Page

2. Navigate to the 'Verified Telephony Connectivity' table (which contains ini files per tested

PBX), by either clicking Verified Telephony Connectivity or scrolling down to the table.

3. In the 'Download' column, click the ZIP file icon corresponding to the required PBX / PSTN

protocol; the 'File Download' message box appears.

4. Click the Save button, navigate to the folder on your PC to where you want to download the

file, and then click Save; the file is downloaded to the folder and when complete, the

'Download Complete' message box appears.

3.3.1.2 Uploading the ini File to the Gateway

Once you have downloaded the correct ini file from the Web, you need to upload it to the

gateway's non-volatile memory using the gateway's Embedded Web Server.

¾ To upload the ini file to the gateway, take these 6 steps:

1. Unzip the downloaded ZIP file that you downloaded in the previous section. An ini file (with

the file extension *.ini) is extracted along with any relevant files.

2. Login to the gateway's Embedded Web Server (refer to Section 3.1.1 on page 10).

3. Open the ‘Configuration File’ screen (Advanced Configuration menu > Configuration

File).

2

Contents

Main Page Table of Contents Page Notices Notice Trademarks WEEE EU Directive Customer Support Abbreviations and Terminology Related Documentation 1 Introduction Page 2 Quick Start 3 Configuring the MediaPack 3.1 Embedded Web Server Management Tool 3.1.1 Accessing the Embedded Web Server To access the Embedded Web Server, take these 4 steps: Page 3.1.3 Changing Login Username and Password To change the user name and password, take these 3 steps: 3.1.4 Searching for ini file Parameters To search for an ini file parameter configurable by the Embedded Web Server, take these 3 steps: 3.2 Assigning an IP Address to the MediaPack 3.2.1 Assigning an IP Address using BootP To assign an IP address using BootP, take these 3 steps: 3.2.2 Assigning an IP Address Using CLI via RS-232 To assign an IP address using CLI via RS-232, take these 5 steps: 3.2.3 Assigning an IP Address using HTTP To assign an IP address to the gateway using HTTP, take these 5 steps: 3.3 Advanced Configuration 3.3.1 Using the ini File 3.3.1.1 Obtaining the ini File from the Web To download the ini file to your PC, take these 4 steps: 3.3.1.2 Uploading the ini File to the Gateway To upload the ini file to the gateway, take these 6 steps: 3.3.1.3 Modifying Parameters Specific to Site Deployment 3.3.2 Using the Embedded Web Server 3.3.2.1 Defining Mediation Server's IP Address To define Mediation Server's IP address, take these 4 steps: 3.3.2.2 Defining Number of FXO Ports Connected to PBX To enable the gateway's FXO ports, take these 4 steps: 3.3.2.3 Defining Voice Coders To define the coder, take these 3 steps: 3.3.2.4 Translating Numbers From / To E.164 Using Manipulation Tables for PBX/PSTN Connectivity To configure the Number Manipulation tables, take these 4 steps: 3.3.2.4.1 Dialing Plan Notation 3.3.2.4.2 Number Normalization Examples Page 3.3.2.5 Defining Answer Supervision To define the Answer Supervision, take these 3 steps: Page 3.3.2.7 Enabling Caller ID To enable Caller ID, take these 3 steps: Page 3.3.2.9 Defining Disconnect on Broken Connection To define Disconnect on Broken Connection, take these 3 steps: 3.3.2.10 Defining DTMF Payload Type To define the DTMF payload type, take these 3 steps: 3.3.2.11 Enabling One-Stage Dialing To enable one-stage dialing, take these 3 steps: 3.3.2.12 Defining Channel Select Mode To define the Channel Select mode, take these 3 steps: 3.3.2.13 Disabling RTCP Attribute To disable the RTCP attribute, take these 5 steps: 4 Backing Up Configuration Settings To save the ini file on your PC, take these 6 steps: 5 Monitoring the Gateway 5.1 Front-Panel LEDs 5.2 Monitoring the Channels To monitor the status of the channels, take this step: To monitor the details of a channel, take these 2 steps: 6 Troubleshooting 6.1 General Troubleshooting 6.2 Restoring Parameters to Factory Default Settings To restore factory default settings, take these 3 steps: 6.3 Debugging using a Syslog Server To configure the Syslog parameters, take these 7 steps: MP-11x & Microsoft Office Communications Server 2007 Quick Installation Guide 42 Document #: LTRT-26301 7 Regulatory Information Declaration of Conformity Quick Installation Guide 7. Regulatory Information Safety Industry Canada Notice Network Compatibility Telecommunication Safety SELV: Safety extra low voltage circuit.