Defining SIP Transport Type | ADTRAN MP-114, MP-118 instruction

Quick Installation Guide

3. Configuring the MediaPack

3.3.2.8Defining SIP Transport Type

The procedure below describes how to configure the SIP transport type. You may need to change the gateway's SIP transport type from UDP (default) to TCP, since this is the transport type used by Mediation Server.

¾To define the SIP transport type, take these 3 steps:

1.Open the ‘General Parameters’ screen (Protocol Management menu > Protocol Definition > General Parameters).

Figure 3-18: General Parameters Screen

2

2.From the ‘SIP Transport Type' drop-down list, select 'TCP'.

3.Click the Submit button to save your changes.

Version 5.0

31

September 2007

Image 31

ADTRAN MP-114, MP-118 manual Defining SIP Transport Type, ¾ To define the SIP transport type, take these 3 steps

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Abbreviations and Terminology TrademarksWeee EU Directive Customer Support Document # Manual Name Related Documentation Network Architecture with PBX Introduction MP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPack Embedded Web Server Management Tool Configuring the MediaPackAccessing the Embedded Web Server ¾ To access the Embedded Web Server, take these 4 steps MediaPack Web Interface Areas Navigating the Embedded Web Server ¾ To change the user name and password, take these 3 steps Changing Login Username and Password Searched Result Screen Searching for ini file Parameters New Client button Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address to the MediaPack Adding a BootP Client Assigning an IP Address Using CLI via RS-232 Quick Setup Screen Assigning an IP Address using Http Using the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Modifying Parameters Specific to Site Deployment Configuration File Screen Defining Mediation Servers IP Address Using the Embedded Web Server ¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps ¾ To define the coder, take these 3 steps Defining Voice Coders Parameter Description Number Manipulation Parameters Description Source IP Dialing Plan Notations Description Example Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision ¾ To define Automatic Dialing, take these 4 steps Defining Automatic Dialing Enabling Caller ID ¾ To enable Caller ID, take these 3 steps ¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type 19 General Parameters Screen Defining Disconnect on Broken Connection ¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload Type Enabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps ¾ To define the Channel Select mode, take these 3 steps Defining Channel Select Mode Disabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps ¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration Settings Front-Panel LEDs Monitoring the Gateway ¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Debugging using a Syslog Server TroubleshootingGeneral Troubleshooting Restoring Parameters to Factory Default Settings Management Settings Screen ¾ To configure the Syslog parameters, take these 7 steps Regulatory Information FCC Statement Telecommunication SafetyIndustry Canada Notice Network Compatibility MediaPack MP-118 & MP-114