Enabling Caller ID | ADTRAN MP-118, MP-114 manual

MP-11x & Microsoft Office Communications Server 2007

3.3.2.7Enabling Caller ID

If the Caller ID service is enabled, the gateway detects the Caller ID signal from the Tel side (PBX

/PSTN) and sends it to Mediation Server over IP in the SIP INVITE message. Therefore, to allow the OCS clients to receive caller ID, enable the Caller ID service at the gateway.

Note: If the deployed PBX does not support Caller ID (and thus, the gateway cannot provide Caller ID), it's recommended to disable the Caller ID service in order to prevent a delay in call establishment.

¾To enable Caller ID, take these 3 steps:

1.Open the 'Supplementary Services' screen (Protocol Management menu > Advanced Parameters > Supplementary Services).

Figure 3-17: Supplementary Services Screen

2

2.From the 'Enable Caller ID' drop-down list, select 'Enable'.

3.Click the Submit button to save your changes.

Quick Installation Guide

30

Document #: LTRT-26301

Image 30

ADTRAN MP-118, MP-114 manual Enabling Caller ID, ¾ To enable Caller ID, take these 3 steps

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Customer Support TrademarksWeee EU Directive Abbreviations and Terminology Related Documentation Document # Manual Name Introduction Network Architecture with PBX MP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start ¾ To access the Embedded Web Server, take these 4 steps Configuring the MediaPackAccessing the Embedded Web Server Embedded Web Server Management Tool Navigating the Embedded Web Server MediaPack Web Interface Areas Changing Login Username and Password ¾ To change the user name and password, take these 3 steps Searching for ini file Parameters Searched Result Screen Assigning an IP Address to the MediaPack Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps New Client button Assigning an IP Address Using CLI via RS-232 Adding a BootP Client Assigning an IP Address using Http Quick Setup Screen Advanced Configuration Using the ini FileObtaining the ini File from the Web ¾ To download the ini file to your PC, take these 4 steps Uploading the ini File to the Gateway¾ To upload the ini file to the gateway, take these 6 steps Configuration File Screen Modifying Parameters Specific to Site Deployment Using the Embedded Web Server Defining Mediation Servers IP Address ¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBX Defining Voice Coders ¾ To define the coder, take these 3 steps Number Manipulation Parameters Description Parameter Description Dialing Plan Notations Description Example Source IP Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 steps Defining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps ¾ To enable Caller ID, take these 3 steps Enabling Caller ID Defining SIP Transport Type ¾ To define the SIP transport type, take these 3 steps Defining Disconnect on Broken Connection 19 General Parameters Screen Defining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps ¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage Dialing Defining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps ¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp Attribute Backing Up Configuration Settings ¾ To save the ini file on your PC, take these 6 steps Monitoring the Gateway Front-Panel LEDs Monitoring the Channels ¾ To monitor the status of the channels, take this step¾ To monitor the details of a channel, take these 2 steps Restoring Parameters to Factory Default Settings TroubleshootingGeneral Troubleshooting Debugging using a Syslog Server ¾ To configure the Syslog parameters, take these 7 steps Management Settings Screen Regulatory Information Network Compatibility Telecommunication SafetyIndustry Canada Notice FCC Statement MediaPack MP-118 & MP-114