Backing Up Configuration Settings | ADTRAN MP-114, MP-118 specification

Quick Installation Guide

4. Backing Up Configuration Settings

4 Backing Up Configuration Settings

Once you have modified configuration settings, it is recommended you make a backup of the modified configuration file. This is done by saving the modified ini configuration file to a folder on your PC. If you lose your gateway's configuration settings, you can always use this backed up ini file to restore them. For a description on uploading (restoring) an ini file to your gateway, refer to Section 3.3.1.2 on page 18.

¾To save the ini file on your PC, take these 6 steps:

1.Login to the gateway's Embedded Web Server (refer to Section 3.1.1 on page 10).

2.Open the ‘Configuration File’ screen (Advanced Configuration menu > Configuration File).

Figure 4-1: Configuration File Screen

3

3.Click the Get ini File button; the ‘File Download’ window opens.

4.Click the Save button; the ‘Save As’ window opens.

5.Navigate to the folder on your PC in which you want to save the ini file.

6.Click the Save button; the gateway copies the ini file to the folder you selected.

Version 5.0

37

September 2007

Image 37

ADTRAN MP-114, MP-118 manual Backing Up Configuration Settings, ¾ To save the ini file on your PC, take these 6 steps

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Weee EU Directive TrademarksCustomer Support Abbreviations and Terminology Document # Manual Name Related Documentation Network Architecture with PBX Introduction MP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPack Accessing the Embedded Web Server Configuring the MediaPack¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management Tool MediaPack Web Interface Areas Navigating the Embedded Web Server ¾ To change the user name and password, take these 3 steps Changing Login Username and Password Searched Result Screen Searching for ini file Parameters ¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address using BootPAssigning an IP Address to the MediaPack New Client button Adding a BootP Client Assigning an IP Address Using CLI via RS-232 Quick Setup Screen Assigning an IP Address using Http Using the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Modifying Parameters Specific to Site Deployment Configuration File Screen Defining Mediation Servers IP Address Using the Embedded Web Server ¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps ¾ To define the coder, take these 3 steps Defining Voice Coders Parameter Description Number Manipulation Parameters Description Source IP Dialing Plan Notations Description Example Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision ¾ To define Automatic Dialing, take these 4 steps Defining Automatic Dialing Enabling Caller ID ¾ To enable Caller ID, take these 3 steps ¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type 19 General Parameters Screen Defining Disconnect on Broken Connection ¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload Type Enabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps ¾ To define the Channel Select mode, take these 3 steps Defining Channel Select Mode Disabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps ¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration Settings Front-Panel LEDs Monitoring the Gateway ¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps General Troubleshooting TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog Server Management Settings Screen ¾ To configure the Syslog parameters, take these 7 steps Regulatory Information Industry Canada Notice Telecommunication SafetyNetwork Compatibility FCC Statement MediaPack MP-118 & MP-114