Assigning an IP Address using Http | ADTRAN MP-118, MP-114 instruction

MP-11x & Microsoft Office Communications Server 2007

3.2.3Assigning an IP Address using HTTP

You can assign an IP address to the gateway using the gateway's Embedded Web Server (based on HTTP), by connecting the gateway to a PC with a direct, local Ethernet connection.

¾To assign an IP address to the gateway using HTTP, take these 5 steps:

1.Connect your PC to the gateway by performing the following:

a.Disconnect the gateway from the network and reconnect it to your PC using one of the following methods:

♦Use a standard Ethernet cable to connect the network interface on your PC to a port on a network hub or switch. Use a second standard Ethernet cable to connect the gateway to another port on the same network hub or switch.

♦Use an Ethernet cross-over cable to directly connect the network interface on your PC to the gateway.

b.Change your PC’s IP address and subnet mask to correspond with the gateway's factory default IP address and subnet mask (listed in Table 3-1).

2.Access the gateway's Embedded Web Server (refer to Section 3.1.1 on page 10); the ‘Quick Setup’ screen is displayed (Quick Setup menu), as shown in the figure below:

Figure 3-6: Quick Setup Screen

3

3

3

Quick Installation Guide

16

Document #: LTRT-26301

Image 16

ADTRAN MP-118, MP-114 manual Assigning an IP Address using Http, Quick Setup Screen

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Trademarks Weee EU DirectiveCustomer Support Abbreviations and Terminology Related Documentation Document # Manual Name Introduction Network Architecture with PBX MP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start Configuring the MediaPack Accessing the Embedded Web Server¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management Tool Navigating the Embedded Web Server MediaPack Web Interface Areas Changing Login Username and Password ¾ To change the user name and password, take these 3 steps Searching for ini file Parameters Searched Result Screen Assigning an IP Address using BootP ¾ To assign an IP address using BootP, take these 3 stepsAssigning an IP Address to the MediaPack New Client button Assigning an IP Address Using CLI via RS-232 Adding a BootP Client Assigning an IP Address using Http Quick Setup Screen Using the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Configuration File Screen Modifying Parameters Specific to Site Deployment Using the Embedded Web Server Defining Mediation Servers IP Address ¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBX Defining Voice Coders ¾ To define the coder, take these 3 steps Number Manipulation Parameters Description Parameter Description Dialing Plan Notations Description Example Source IP Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 steps Defining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps ¾ To enable Caller ID, take these 3 steps Enabling Caller ID Defining SIP Transport Type ¾ To define the SIP transport type, take these 3 steps Defining Disconnect on Broken Connection 19 General Parameters Screen Defining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps ¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage Dialing Defining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps ¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp Attribute Backing Up Configuration Settings ¾ To save the ini file on your PC, take these 6 steps Monitoring the Gateway Front-Panel LEDs ¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Troubleshooting General TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog Server ¾ To configure the Syslog parameters, take these 7 steps Management Settings Screen Regulatory Information Telecommunication Safety Industry Canada NoticeNetwork Compatibility FCC Statement MediaPack MP-118 & MP-114