Management Settings Screen | ADTRAN MP-114, MP-118 instruction

Quick Installation Guide

6. Troubleshooting

¾To configure the Syslog parameters, take these 7 steps:

1.Open the ‘Management Settings’ screen (Advanced Configuration menu > Management Settings); the ‘Management Settings’ screen is displayed.

Figure 6-1: Management Settings Screen

2 3 4

5

2.In the 'Syslog Server IP Address' field, enter the Syslog's IP address. Note that the Syslog server's IP address must correspond to the network environment in which the Syslog server is installed.

3.In the 'Syslog Server Port' field, enter the UDP port number (default port is 514).

4.From the 'Enable Syslog' drop-down list, enable the Syslog feature by selecting 'Enable'.

5.In the 'Activity Types to Report' group, select the Web operations that you want logged to the Syslog server.

6.To define the messages based on severity level that you want sent to the Syslog server, open the ‘General Parameters’ screen (Protocol Management menu > Advanced Parameters > General Parameters), and then from the 'Debug Level' drop-down list, select '5' (i.e., all reports with severity level 5 are sent to the Syslog server).

7.To enable additional call information sent to the Syslog, in the 'CDR Report Level' drop-down list, select 'End Call'

Version 5.0

41

September 2007

Image 41

ADTRAN MP-114, MP-118 manual ¾ To configure the Syslog parameters, take these 7 steps, Management Settings Screen

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Weee EU Directive TrademarksCustomer Support Abbreviations and Terminology Document # Manual Name Related Documentation Network Architecture with PBX Introduction MP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPack Accessing the Embedded Web Server Configuring the MediaPack¾ To access the Embedded Web Server, take these 4 steps Embedded Web Server Management Tool MediaPack Web Interface Areas Navigating the Embedded Web Server ¾ To change the user name and password, take these 3 steps Changing Login Username and Password Searched Result Screen Searching for ini file Parameters ¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address using BootPAssigning an IP Address to the MediaPack New Client button Adding a BootP Client Assigning an IP Address Using CLI via RS-232 Quick Setup Screen Assigning an IP Address using Http Obtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Modifying Parameters Specific to Site Deployment Configuration File Screen Defining Mediation Servers IP Address Using the Embedded Web Server ¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps ¾ To define the coder, take these 3 steps Defining Voice Coders Parameter Description Number Manipulation Parameters Description Source IP Dialing Plan Notations Description Example Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision ¾ To define Automatic Dialing, take these 4 steps Defining Automatic Dialing Enabling Caller ID ¾ To enable Caller ID, take these 3 steps ¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type 19 General Parameters Screen Defining Disconnect on Broken Connection ¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload Type Enabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps ¾ To define the Channel Select mode, take these 3 steps Defining Channel Select Mode Disabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps ¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration Settings Front-Panel LEDs Monitoring the Gateway ¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step General Troubleshooting TroubleshootingRestoring Parameters to Factory Default Settings Debugging using a Syslog Server Management Settings Screen ¾ To configure the Syslog parameters, take these 7 steps Regulatory Information Industry Canada Notice Telecommunication SafetyNetwork Compatibility FCC Statement MediaPack MP-118 & MP-114