Enabling One-Stage Dialing | ADTRAN MP-118, MP-114 guide

MP-11x & Microsoft Office Communications Server 2007

3.3.2.11 Enabling One-Stage Dialing

One-stage dialing is when the gateway receives an IP-to-Tel call, off-hooks the PBX line connected to the PBX / PSTN telephone, and then immediately dials the destination telephone number. In other words, the OCS client (i.e., IP caller) doesn't dial the PSTN number upon hearing a dial tone.

¾To enable one-stage dialing, take these 3 steps:

1.Open the ‘FXO Settings’ screen (Protocol Management menu > Advanced Applications > FXO Settings); the ‘FXO Settings’ screen is displayed.

Figure 3-21: FXO Settings Screen

2

2.From the 'Dialing Mode' drop-down list, select 'One Stage'.

3.Click the Submit button to save your changes.

Quick Installation Guide

34

Document #: LTRT-26301

Image 34

ADTRAN MP-118, MP-114 manual Enabling One-Stage Dialing, ¾ To enable one-stage dialing, take these 3 steps

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Customer Support TrademarksWeee EU Directive Abbreviations and Terminology Related Documentation Document # Manual Name Introduction Network Architecture with PBX MP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start ¾ To access the Embedded Web Server, take these 4 steps Configuring the MediaPackAccessing the Embedded Web Server Embedded Web Server Management Tool Navigating the Embedded Web Server MediaPack Web Interface Areas Changing Login Username and Password ¾ To change the user name and password, take these 3 steps Searching for ini file Parameters Searched Result Screen Assigning an IP Address to the MediaPack Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps New Client button Assigning an IP Address Using CLI via RS-232 Adding a BootP Client Assigning an IP Address using Http Quick Setup Screen Using the ini File Advanced ConfigurationObtaining the ini File from the Web Uploading the ini File to the Gateway ¾ To download the ini file to your PC, take these 4 steps¾ To upload the ini file to the gateway, take these 6 steps Configuration File Screen Modifying Parameters Specific to Site Deployment Using the Embedded Web Server Defining Mediation Servers IP Address ¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBX Defining Voice Coders ¾ To define the coder, take these 3 steps Number Manipulation Parameters Description Parameter Description Dialing Plan Notations Description Example Source IP Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 steps Defining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps ¾ To enable Caller ID, take these 3 steps Enabling Caller ID Defining SIP Transport Type ¾ To define the SIP transport type, take these 3 steps Defining Disconnect on Broken Connection 19 General Parameters Screen Defining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps ¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage Dialing Defining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps ¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp Attribute Backing Up Configuration Settings ¾ To save the ini file on your PC, take these 6 steps Monitoring the Gateway Front-Panel LEDs ¾ To monitor the status of the channels, take this step Monitoring the Channels¾ To monitor the details of a channel, take these 2 steps Restoring Parameters to Factory Default Settings TroubleshootingGeneral Troubleshooting Debugging using a Syslog Server ¾ To configure the Syslog parameters, take these 7 steps Management Settings Screen Regulatory Information Network Compatibility Telecommunication SafetyIndustry Canada Notice FCC Statement MediaPack MP-118 & MP-114