Defining Channel Select Mode | ADTRAN MP-114, MP-118 manual

Quick Installation Guide

3. Configuring the MediaPack

3.3.2.12 Defining Channel Select Mode

Channel select modes determine the method in which new IP-to-Tel calls (i.e., calls from OCS clients to PBX/PSTN phones) are assigned to gateway ports (i.e., channels). It is recommended to select the Cyclic Ascending mode, which selects the next available channel in an ascending cycle order.

¾To define the Channel Select mode, take these 3 steps:

1.Open the 'General' screen (Protocol Management menu > Protocol Definition > General Parameters).

Figure 3-22: General Screen

2

2.From the 'Channel Select Mode' drop-down list, select 'Cyclic Ascending'.

3.Click the Submit button to save your changes.

Version 5.0

35

September 2007

Image 35

ADTRAN MP-114, MP-118 manual Defining Channel Select Mode, ¾ To define the Channel Select mode, take these 3 steps

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Abbreviations and Terminology TrademarksWeee EU Directive Customer Support Document # Manual Name Related Documentation Network Architecture with PBX Introduction MP-11x & Microsoft Office Communications Server Quick Start Required Steps to Install MediaPack Embedded Web Server Management Tool Configuring the MediaPackAccessing the Embedded Web Server ¾ To access the Embedded Web Server, take these 4 steps MediaPack Web Interface Areas Navigating the Embedded Web Server ¾ To change the user name and password, take these 3 steps Changing Login Username and Password Searched Result Screen Searching for ini file Parameters New Client button Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps Assigning an IP Address to the MediaPack Adding a BootP Client Assigning an IP Address Using CLI via RS-232 Quick Setup Screen Assigning an IP Address using Http Obtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Modifying Parameters Specific to Site Deployment Configuration File Screen Defining Mediation Servers IP Address Using the Embedded Web Server ¾ To define Mediation Servers IP address, take these 4 steps Defining Number of FXO Ports Connected to PBX ¾ To enable the gateways FXO ports, take these 4 steps ¾ To define the coder, take these 3 steps Defining Voice Coders Parameter Description Number Manipulation Parameters Description Source IP Dialing Plan Notations Description Example Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls ¾ To define the Answer Supervision, take these 3 steps Defining Answer Supervision ¾ To define Automatic Dialing, take these 4 steps Defining Automatic Dialing Enabling Caller ID ¾ To enable Caller ID, take these 3 steps ¾ To define the SIP transport type, take these 3 steps Defining SIP Transport Type 19 General Parameters Screen Defining Disconnect on Broken Connection ¾ To define the Dtmf payload type, take these 3 steps Defining Dtmf Payload Type Enabling One-Stage Dialing ¾ To enable one-stage dialing, take these 3 steps ¾ To define the Channel Select mode, take these 3 steps Defining Channel Select Mode Disabling Rtcp Attribute ¾ To disable the Rtcp attribute, take these 5 steps ¾ To save the ini file on your PC, take these 6 steps Backing Up Configuration Settings Front-Panel LEDs Monitoring the Gateway ¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Debugging using a Syslog Server TroubleshootingGeneral Troubleshooting Restoring Parameters to Factory Default Settings Management Settings Screen ¾ To configure the Syslog parameters, take these 7 steps Regulatory Information FCC Statement Telecommunication SafetyIndustry Canada Notice Network Compatibility MediaPack MP-118 & MP-114