Assigning an IP Address to the MediaPack | ADTRAN MP-118, MP-114

MP-11x & Microsoft Office Communications Server 2007

3.2Assigning an IP Address to the MediaPack

If the gateway's default IP address (refer to Table 3-1)doesn't correspond to the network in which Office Communications Server 2007 is installed, you can assign a different IP address to the gateway, using one of the following methods:

BootP (refer to Section 3.2.1 on page 14)

Command Line Interface (CLI) using the RS-232 interface (refer to Section 3.2.2 on page 15)

Gateway's HTTP-based Embedded Web Server (refer to Section 3.2.3 on page 16)

DHCP (refer to the gateway's User’s Manual)

Table 3-1: Gateway Default Networking Parameters

Network Parameter	Default Value

IP address	10.1.10.11

Default subnet mask	255.255.0.0

Default gateway IP address	0.0.0.0

You can use the hardware reset button to restore the gateway's networking parameters to their factory default values (refer to Section 6.2 on page 40).

3.2.1Assigning an IP Address using BootP

You can use AudioCodes' Bootstrap Protocol (BootP) or any third-party BootP application to assign an IP address to the gateway.

¾To assign an IP address using BootP, take these 3 steps:

1.Open the BootP application.

2.Add a new client by performing the following (for AudioCodes BootP Server application):

a.From the Services menu, choose Clients; the Client Configuration dialog box appears.

b.Add a client configuration for the gateway that you want to initialize, by clicking the Add

New Client button.

c.Enter the necessary fields (i.e., gateway's MAC address and desired IP address), and then click OK.

Quick Installation Guide

14

Document #: LTRT-26301

Image 14

ADTRAN MP-118, MP-114 Assigning an IP Address to the MediaPack, Assigning an IP Address using BootP, New Client button

Contents

MediaPack MP-118 & MP-114 Page Table of Contents Readers Notes Customer Support TrademarksWeee EU Directive Abbreviations and Terminology Related Documentation Document # Manual Name Introduction Network Architecture with PBX MP-11x & Microsoft Office Communications Server Required Steps to Install MediaPack Quick Start ¾ To access the Embedded Web Server, take these 4 steps Configuring the MediaPackAccessing the Embedded Web Server Embedded Web Server Management Tool Navigating the Embedded Web Server MediaPack Web Interface Areas Changing Login Username and Password ¾ To change the user name and password, take these 3 steps Searching for ini file Parameters Searched Result Screen Assigning an IP Address to the MediaPack Assigning an IP Address using BootP¾ To assign an IP address using BootP, take these 3 steps New Client button Assigning an IP Address Using CLI via RS-232 Adding a BootP Client Assigning an IP Address using Http Quick Setup Screen Obtaining the ini File from the Web Advanced ConfigurationUsing the ini File ¾ To upload the ini file to the gateway, take these 6 steps ¾ To download the ini file to your PC, take these 4 stepsUploading the ini File to the Gateway Configuration File Screen Modifying Parameters Specific to Site Deployment Using the Embedded Web Server Defining Mediation Servers IP Address ¾ To define Mediation Servers IP address, take these 4 steps ¾ To enable the gateways FXO ports, take these 4 steps Defining Number of FXO Ports Connected to PBX Defining Voice Coders ¾ To define the coder, take these 3 steps Number Manipulation Parameters Description Parameter Description Dialing Plan Notations Description Example Source IP Number Normalization Examples 14 Phone Number Manipulation Table for TelÆIP Calls Defining Answer Supervision ¾ To define the Answer Supervision, take these 3 steps Defining Automatic Dialing ¾ To define Automatic Dialing, take these 4 steps ¾ To enable Caller ID, take these 3 steps Enabling Caller ID Defining SIP Transport Type ¾ To define the SIP transport type, take these 3 steps Defining Disconnect on Broken Connection 19 General Parameters Screen Defining Dtmf Payload Type ¾ To define the Dtmf payload type, take these 3 steps ¾ To enable one-stage dialing, take these 3 steps Enabling One-Stage Dialing Defining Channel Select Mode ¾ To define the Channel Select mode, take these 3 steps ¾ To disable the Rtcp attribute, take these 5 steps Disabling Rtcp Attribute Backing Up Configuration Settings ¾ To save the ini file on your PC, take these 6 steps Monitoring the Gateway Front-Panel LEDs ¾ To monitor the details of a channel, take these 2 steps Monitoring the Channels¾ To monitor the status of the channels, take this step Restoring Parameters to Factory Default Settings TroubleshootingGeneral Troubleshooting Debugging using a Syslog Server ¾ To configure the Syslog parameters, take these 7 steps Management Settings Screen Regulatory Information Network Compatibility Telecommunication SafetyIndustry Canada Notice FCC Statement MediaPack MP-118 & MP-114