Main
Page
Table of Contents
Page
Notices Notice
Trademarks
WEEE EU Directive
Customer Support
Abbreviations and Terminology
Related Documentation
1 Introduction
Page
2 Quick Start
3 Configuring the MediaPack
3.1 Embedded Web Server Management Tool
3.1.1 Accessing the Embedded Web Server
To access the Embedded Web Server, take these 4 steps:
Page
3.1.3 Changing Login Username and Password
To change the user name and password, take these 3 steps:
3.1.4 Searching for ini file Parameters
To search for an ini file parameter configurable by the Embedded Web Server, take these 3 steps:
3.2 Assigning an IP Address to the MediaPack
3.2.1 Assigning an IP Address using BootP
To assign an IP address using BootP, take these 3 steps:
3.2.2 Assigning an IP Address Using CLI via RS-232
To assign an IP address using CLI via RS-232, take these 5 steps:
3.2.3 Assigning an IP Address using HTTP
To assign an IP address to the gateway using HTTP, take these 5 steps:
3.3 Advanced Configuration
3.3.1 Using the ini File
3.3.1.1 Obtaining the ini File from the Web
To download the ini file to your PC, take these 4 steps:
3.3.1.2 Uploading the ini File to the Gateway
To upload the ini file to the gateway, take these 6 steps:
3.3.1.3 Modifying Parameters Specific to Site Deployment
3.3.2 Using the Embedded Web Server
3.3.2.1 Defining Mediation Server's IP Address
To define Mediation Server's IP address, take these 4 steps:
3.3.2.2 Defining Number of FXO Ports Connected to PBX
To enable the gateway's FXO ports, take these 4 steps:
3.3.2.3 Defining Voice Coders
To define the coder, take these 3 steps:
3.3.2.4 Translating Numbers From / To E.164 Using Manipulation Tables for PBX/PSTN Connectivity
To configure the Number Manipulation tables, take these 4 steps:
3.3.2.4.1 Dialing Plan Notation
3.3.2.4.2 Number Normalization Examples
Page
3.3.2.5 Defining Answer Supervision
To define the Answer Supervision, take these 3 steps:
Page
3.3.2.7 Enabling Caller ID
To enable Caller ID, take these 3 steps:
Page
3.3.2.9 Defining Disconnect on Broken Connection
To define Disconnect on Broken Connection, take these 3 steps:
3.3.2.10 Defining DTMF Payload Type
To define the DTMF payload type, take these 3 steps:
3.3.2.11 Enabling One-Stage Dialing
To enable one-stage dialing, take these 3 steps:
3.3.2.12 Defining Channel Select Mode
To define the Channel Select mode, take these 3 steps:
3.3.2.13 Disabling RTCP Attribute
To disable the RTCP attribute, take these 5 steps:
4 Backing Up Configuration Settings
To save the ini file on your PC, take these 6 steps:
5 Monitoring the Gateway
5.1 Front-Panel LEDs
5.2 Monitoring the Channels
To monitor the status of the channels, take this step:
To monitor the details of a channel, take these 2 steps:
6 Troubleshooting
6.1 General Troubleshooting
6.2 Restoring Parameters to Factory Default Settings
To restore factory default settings, take these 3 steps:
6.3 Debugging using a Syslog Server
To configure the Syslog parameters, take these 7 steps:
MP-11x & Microsoft Office Communications Server 2007
Quick Installation Guide 42 Document #: LTRT-26301
7 Regulatory Information
Declaration of Conformity
Quick Installation Guide 7. Regulatory Information
Safety
Industry Canada Notice
Network Compatibility
Telecommunication Safety
SELV: Safety extra low voltage circuit.