Manuals / Agilent Technologies / Computer Equipment / Power Supply

Agilent Technologies 6614C, 6634B SENSe WINDow, HANNing, RECTangular, Returned Parameters CRD

Models: 6632B 6633B 66332A 6634B

1 103

Download 103 pages 34 Kb

Page 54

4 - Language Dictionary

SENSe:WINDow

This command sets the window function that is used in output measurement calculations. The following functions can be selected:

HANNing	A signal conditioning window that reduces errors in dc and rms measurement
	calculations in the presence of periodic signals such as line ripple. It also
	reduces jitter when measuring successive pulse waveforms. The Hanning
	window multiplies each point in the measurement sample by the function cos4.
	Do not use the Hanning window when measuring single-shot pulse waveforms.
RECTangular	A window that returns measurement calculations without any signal
	conditioning. This window may be used for pulse measurements where the
	exact period of the pulse waveform is known and the measurement interval can
	be set accordingly using the SENSe:SWEep:TINTerval command.

NOTE:	Neither window function alters the instantaneous voltage or current data returned in the
	measurement array.

Command Syntax SENSe:WINDow[:TYPE] <type> Parameters HANNing RECTangular *RST Value HANNing

Examples SENS:WIND RECT Query Syntax SENSe:WINDow[:TYPE]?

Returned Parameters <CRD>

54

Image 54

Agilent Technologies 6614C, 6634B, 66332A, 6633B, 6632B, 6613C SENSe WINDow, HANNing, RECTangular, Returned Parameters CRD

Contents

Dynamic Measurement DC Source System DC Power SupplyProgramming Guide Agilent Models 66312A, 66332ASafety Guidelines Printing History2 - INTRODUCTION TO PROGRAMMING Table of Contents1 - GENERAL INFORMATION 3 - PROGRAMMING THE DC SOURCE4 - LANGUAGE DICTIONARY Output Commands Status CommandsB - COMPATIBILITY LANGUAGE C - ERROR MESSAGESA - SCPI CONFORMANCE INFORMATION D - EXAMPLE PROGRAMSGeneral Information About this GuideDocumentation Summary External References GPIB ReferencesSCPI References Introduction to Programming VXIplug&play Power Products Instrument DriversDownloading and Installing the Driver Supported ApplicationsRS-232Capabilities of the DC Source Accessing Online HelpGPIB Capabilities of the DC Source GPIB AddressRS-232Flow Control RS-232Programming ExampleBaud Rate RS-232Troubleshooting Introduction to SCPIConventions Used in This Guide Types of SCPI Commands Multiple Commands in a MessageTypes of SCPI Messages Including Common CommandsUsing Queries Moving Among SubsystemsHeaders Query IndicatorThe Message Unit Message Unit SeparatorSuffixes and Multipliers SCPI Data FormatsNumerical Data Formats Response Data TypesSCPI Command Completion Using Device ClearPage Introduction Power-onInitializationProgramming the DC Source Programming the OutputMaximum Voltage Output VoltageOutput Current Maximum CurrentSCPI Triggering Nomenclature Setting the Voltage or Current Trigger LevelsTriggering Output Changes Output Trigger System ModelInitiating the Output Trigger System Generating TriggersMaking Measurements Voltage and Current MeasurementsRMS Measurements Agilent 66312A, 66332A Only Current RangesInternally Triggered Measurements Measurement Trigger System ModelSCPI Triggering Nomenclature 3 - Programming the DC Source Page Current Detector Pulse Measurement QueriesControlling Measurement Samples Varying the Voltage or Current Sampling RateMultiple Measurements Agilent 66312A, 66332A Only Figure 3-6. Pre-eventand Post-eventTriggering Programming the DC Source Power-OnConditions Programming the Status RegistersRQS ,**$ Signal Operation Status GroupTable 3-1.Bit Configurations of Status Registers CommandStatus Byte Register Questionable Status GroupStandard Event Status Group CommandThe RQS Bit Determining the Cause of a Service InterruptThe MSS Bit The MAV Bit and Output QueueDiscrete Fault Indicator DFI Inhibit/Fault IndicatorMonitoring Both Phases of a Status Transition Remote Inhibit RIFAULT/INHIBIT Using the Inhibit/Fault Port as a Digital I/ODFI Programming Example Bit WeightPage Subsystem Commands Language DictionaryIntroduction Table 4-1.Subsystem Commands Syntax Table 4-1.Subsystem Commands Syntax continued Table 4-1.Subsystem Commands Syntax continued Table 4-2.Common Commands Syntax Common CommandsProgramming Parameters Table 4-3.Output Programming ParametersCALibrate CURRent NEGative Calibration CommandsCALibrate CURRent CALibrate CURRent MEASure LOWRangeCALibrate LEVel CALibrate PASSwordCALibrate DATA CALibrate SAVECALibrate VOLTage PROTection CALibrate STATeCALibrate VOLTage CAL STAT 1,6812 CAL STAT OFFMeasurement Commands MEASure ARRay CURRent? FETCh ARRay CURRent?MEASure ARRay VOLTage? FETCh ARRay VOLTage? MEASure CURRent? FETCh CURRent? MEASure CURRent ACDC? FETCh CURRent ACDC?MEASure CURRent HIGH? FETCh CURRent HIGH? MEASure CURRent LOW? FETCh CURRent LOW? MEASure CURRent MAXimum? FETCh CURRent MAXimum?MEASure CURRent MINimum? FETCh CURRent MINimum? MEASure VOLTage? FETCh VOLTage? MEASure VOLTage ACDC? FETCh VOLTage ACDC?MEASure VOLTage HIGH? FETCh VOLTage HIGH? MEASure VOLTage LOW? FETCh VOLTage LOW? MEASure VOLTage MAXimum? FETCh VOLTage MAXimum?MEASure VOLTage MINimum? FETCh VOLTage MINimum? SENSe CURRent RANGe SENSe CURRent DETectorSENS CURR DET ACDC SENSe:SWEep:POINts SENSe FUNCtionSENSe SWEep OFFSet POINts SENSe SWEep TINTervalRECTangular SENSe WINDowHANNing Returned Parameters CRDOUTPut DFI Output CommandsOUTPut OUTPut DFI SOURceOUTPut PROTection CLEar OUTPut PROTection DELayOUTPut PON STATe OUTP PON STAT RSTOUTPut RI MODE OUTPut RELayOUTPut RELay POLarity OUTP REL POL NORMSOURce CURRent PROTection STATe SOURce CURRentSOURce CURRent TRIGger CURR PROT STAT 1CURRENT PROTECTION STATE ONSOURce VOLTage SOURce DIGital DATASOURce DIGital FUNCtion DIG DATASOURce VOLTage TRIGger SOURce VOLTage ALC BANDwidth?SOURce VOLTage ALC BWIDth? SOURce VOLTage PROTectionSTATus OPERation? Status CommandsSTATus PRESet STATus OPERation CONDition?STATus OPERation ENABle STATUS OPERATION ENABLE?STATus OPERation NTR STATus OPERation PTR STATus QUEStionable CONDition? STATus QUEStionable ENABleSTATus QUEStionable? STAT QUES COND? STATUS QUESTIONABLE CONDITION?Preset Value STATus QUEStionable NTR STATus QUEStionable PTRCommand Syntax Related CommandsQuery Syntax Returned Parameters Related Commands ESR?Command Syntax Parameters Power-OnValue Examples Related CommandsPage STB? DISPlay System CommandsDISP TEXT DEFAULT MODE DISPlay MODESYSTem VERSion? SYSTem ERRor?SYSTem LANGuage Query Syntax SYSTem ERRor? Parameters NoneSYSTem RWLock SYSTem LOCalSYSTem:REMote IDN?OPT? TST? INITiate SEQuence INITiate NAME Trigger CommandsABORt INITiate CONTinuous SEQuence1TRIGger TRIGger SOURceTRIGger SEQuence2 TRIGger ACQuire TRIGger SEQuence2 COUNt VOLTage TRIGger SEQuence2 COUNt CURRentTRIGger ACQuire COUNt CURRent TRIGger ACQuire COUNt VOLTageTRIGger SEQuence2 HYSTeresis VOLTage TRIGger SEQuence2 HYSTeresis CURRentTRIGger ACQuire HYSTeresis CURRent TRIGger ACQuire HYSTeresis VOLTageTRIGger SEQuence2 LEVel VOLTage TRIGger SEQuence2 LEVel CURRentTRIGger ACQuire LEVel CURRent TRIGger ACQuire LEVel VOLTageTRIGger SEQuence2 SLOPe VOLTage TRIGger SEQuence2 SLOPe CURRentTRIGger ACQuire SLOPe CURRent TRIGger ACQuire SLOPe VOLTageTRIGger SEQuence2 SOURce TRIGger ACQuire SOURce TRIGger SEQuence1 DEFine TRIGger SEQuence2 DEFinePage SCPI Conformance Information SCPI Confirmed CommandsNon-SCPICommands SCPI VersionPage Compatibility Language IntroductionSimilar SCPI Command Table B-2.COMPatibility CommandsCompatibility Command DescriptionCommand Compatibility CommandTable B-2.COMPatibility Commands continued DescriptionTable B-2.COMPatibility Commands continued Figure B-1.COMpatibility Status Model Page Error Messages Error Number ListTable C-1.Error Numbers continued Error NumberError String Description/Explanation/Examples Error Number Table C-1.Error Numbers continuedError String Description/Explanation/Examples Page Types of DOS Drivers Example ProgramsAssigning the GPIB Address in Programs IntroductionError Handling BASIC ControllersExample Programs - D 990’----------------------Merge DECL.BAS here 1225 Example 3. Controller Using BASIC INDEX Index Page waiting for measurement results varying voltage or current sampling, 29 voltagemaximum, 20 measurements XON-XOFF,111/4/00 Manual Updates11/9/99 All references to HP have been changed to Agilent