Manuals / Airlink101 / Photography / Security Camera

Airlink101 AIC250W user manual Configuration - Video

Models: AIC250W

1 84

Download 84 pages 23.68 Kb

Page 29

8.2.2 Configuration – Video

8.2.2 Configuration – Video

The Configuration – Video page allows you to configure the Video Settings of the Camera.

Video Resolution: Select the desired video resolution.

Compression Rate: Select the desired video compression rate. Higher compression rate yields smaller file size but with less video quality and vice versa.

Frame Rate: Select the desired frame rate.

Brightness Control: Adjust the brightness level.

Contrast Control: Adjust the contrast level.

Saturation Control: Adjust the saturation level.

Light Frequency: Adjust the light frequency.

Mirror: Select to apply horizontal or vertical mirroring.

Anti-Flicker:Check to enable anti-flicker.

Click Save to apply the new settings.

29

Image 29

Airlink101 AIC250W user manual Configuration - Video

Contents

Ver. 1B SkyIPCam 250W Wireless Network CameraModel # AIC250W User’s Manual Table of Contents 10.4.2 Web Configuration 10.4.1 Camera Configuration10.4.3 Motion Configuration-1 10.4.4 Motion Configuration-21. Introduction Package Contents2. Getting Started 1. Connect the IP Camera to your network 2. Install the Setup Wizard4. Configure the IP Camera using the Setup Wizard Step 3 Click Next 3. Installing the Setup WizardStep 2 Click on Install Wizard Step 4 Click Yes to accept the License Agreement Step 5 Click Next to accept the default Destination FolderStep 6 Click Finish to complete the installation 4. Gathering Information 1. Network ID SSID 2. Channel Number 3. Wireless Encryption SettingsStep 1 Go to Start All Programs AirLink101 IP Camera Setup Wizard 5. Using the Setup WizardStep 4 Enter admin for both the Admin ID and Password and click OK Note If you do not receive this message, skip to StepPage Page Step 11 If you need to change the Camera’s IP Address because another network device is already using the same address, you can assign a new address here and click Next WPA-PSK Step 14 Click Next 6. Viewing Images Step 3 Turn the Camera’s lens clockwise or counter-clockwise to focus The IP Camera is ready for use now7.1 Infrastructure Mode 7. Configuring Wireless SettingsStep 3 Enter admin for both the User name and Password and click OK Step 4 Click on Configuration and then WirelessStep 7 Click Save to apply the new settings Step 8 Click on Management and go to Wireless. Verify that the Connection Mode is Infrastructure and the Link is Yes. Also verify that the SSID matches the SSID of your wireless router 7.2 Ad-Hoc Mode Step 5 Click Save 8. Web Configuration Utility 8.1.1 Management - System 8.1.2 Management - Video 8.1.3 Management - Wireless8.1.5 Management - User 8.1.4 Management - NetworkLED Control 8.2.1 Configuration - System8.2.2 Configuration - Video 8.2.3 Configuration - Wireless Encryption Wireless InterfaceWEP Encryption Authentication Type Choose from Open System, Shared Key, or BothPreamble Select long or short preamble Advanced SettingWPA-PSK Encryption IP Address Mode 8.2.4 Configuration - Network8.2.5 Configuration - User 8.2.6 Configuration - Date & Time 8.2.7 Configuration - Upload 8.2.8 Configuration - E-mail 8.3.2 Tools - E-mail Test 8.3.1 Tools - FTP Server Test8.3.4 Tools - Factory Reset 8.3.3 Tools - ResetThe Tools - Reset page allows you to Reset the Camera Click on Yes to perform the reset8.3.5 Tools - Firmware Upgrade 8.4.1 Help - About 8.3.6 Tools - BackupConfig.bin Example 9. Viewing Videos from External NetworksStep 4 Click on Configuration then Network Ex. http//172.16.1.181 Step 2 Click on Install IPView Pro 10.1 Installing IPView Pro10. IPView Pro Step 3 Click NextStep 4 Click Yes to accept the License Agreement Step 5 Click Next to accept the default Destination FolderStep 6 Click Finish to complete the installation IPView Pro 10.2 Starting IPView ProStep 1 Click on the System Configuration button 10.2.1 Adding Camera using the Search MethodPage Step 7 Click Save to apply the changes Step 6 You should see your camera added to the Camera ListPage 10.2.2 Adding Camera using the Input IP Method Step 5 Click Save to apply the changes Step 4 You should see your camera added to the Camera ListThis section describes the various features of IPView Pro 10.3 Using IPView Pro10.3.1 Status Mode Window Zoom Mode Adjusts the zoom setting of the camera Audio Disabled for this modelUse the Camera Buttons to control the camera’s various functions From left to right10.3.2 View Window and View Mode Buttons 10.3.3 Control Panel Button to open the System Configuration Window System Configuration Click on the System Configuration10.4.1 Camera Configuration 10.4 System Configuration10.4.2 Web Configuration At the Record Button, select Motion Record 10.4.3 Motion Configuration-1Motion Options 10.4.4 Motion Configuration-210.4.5 Tools Update Firmware10.4.6 Mail Configuration 10.4.7 Proxy Server 500 MB - 1000 MB 10.4.8 Recording ConfigurationDate Mode 10.4.9 Schedule-Recording ConfigurationSpecify the Start Date/Time and the Stop Date/Time and click Add At the Record Button, select Schedule RecordAt the Record Button, select Schedule Record Week Mode10.4.10 Others Select the desired camera from the drop-down menu to display its log 10.4.11 Log ListThe Log List page displays the log of the selected camera 10.4.12 Account The About page provides the version number of IPView Pro 10.4.13 About11. Xplug Control 11.1 Installing Xplug ControlStep 2 Select the Security tab and click on Custom Level 11.2 Enabling ActiveXAutomatic prompting for ActiveX controls Enable Step 3 Verify the following settings are enabled. Click OK when doneRun ActiveX controls and plug-ins Enable Download signed ActiveX controls PromptStep 5 The video should appear now Sending Images via Web Browser AppendixPage Step 5 Verify that the new user account is listed in the User List Page Page Toll Free Technical SupportE-mail support@airlink101.com