Manuals / Brands / Computer Equipment / Switch / Allied Telesis / Computer Equipment / Switch

Allied Telesis at-8116 get-stst-level, set-stst-level <level>, warm-reset, cold-reset, get-last-err

1 88

Download 88 pages, 238.82 Kb

AT-8116 User’s Guide

4-3

get-stst-level

This command shows the self-test level (Disable or Enable) of the

device.

Default Value: Enable

set-stst-level <level>

This command sets the self-test level of the device. There are two

levels of self-test: Disable and Enable. The self-test level is stored in

Non-volatile Random Access Memory (NVRAM).

warm-reset

The warm-reset command resets the SNMP Agent software. The

Switch conﬁguration is changed according to the values stored in

the NVRAM. This command will permit the user to refresh the Switch

conﬁguration after a change of the NVRAM parameters. The statistics

counters are also reset by the warm-reset command.

cold-reset

This command causes the switch to cold-reset. Cold reset is

equivalent to power on the switch.

get-last-err

This command retrieves the most recent system failure for diagnostic

purposes.

SYS_console>get-last-err

System information since the last hardware

reset

--------------------------------------------

Software resets number: 0

The system never encountered a fatal error

SYS_console>

Note

Software resets number implies executed “warm resets” commands

after last “cold reset”.

Contents

Main Page Table of Contents Page Chapter 1 Administrative Interface Features Page Network Management Systems Accessing the SNMP Agent System Requirements VT100 Terminal Settings Testing the Installation Accessing the Command Line Interface Remotely Page Chapter 2 Command Line Interface Features of the Command Line Interface Entering Commands Page System Commands Command Line Interface Structure Page Chapter 3 Console Commands Page set-attr-prompt set-attr-msg set-attr-text set-passwd Page Chapter 4 System Commands sys-stat SYS_console> get-stst-level set-stst-level <level> warm-reset cold-reset get-last-err Page sw-dnld set-fg-param start-fg stop-fg Chapter 5 IP Commands get-ip set-ip get-ip-cfg set-ip-cfg clear-ip-cfg get-gatew set-gatew Chapter 6 Address Resolution Commands get-arp-tbl del-arp-entry add-arp-entry Chapter 7 Ping Commands Page Page Page Chapter 8 SNMP Commands SNMP Community String Commands get-comm set-comm SNMP Trap Message Commands get-auth set-auth get-traps add-trap del-trap get-rmon-state Chapter 9 Switching Database Commands Learning Table get-lt-entry get-lt-16 find-lt-addr del-lt-entry del-lt-addr add-lt-entry get-lt-age set-lt-age Page Chapter 10 Virtual LAN Commands Virtual Broadcast Domains (VBC) get-con-matrix Page del-vbc-domain get-vbc-matrix Security VLANs set-sec-vlan del-sec-vlan get-svlan-tbl get-svlan-matrix Page Chapter 11 Port Monitoring Commands set-mon-port stop-mon get-nv-mon Page Chapter 12 Port Conguration Commands get-port-cfg set-port-dplex set-speed-sel set-port-state set-aggr-mode Page Chapter 13 Switching Statistics Commands clr-cnt Page get-colls-cnt get-rmon-cnt get-sdist-cnt get-mgm-brcnt Chapter 14 Spanning Tree Commands get-stp set-stp Page Page Page Chapter 15 Using an SNMP Manager Configuring the AT-8116 SNMP Agent Global Setup IP Setup SNMP Setup Page Chapter 16 Software Troubleshooting Page Appendix A Software Downloading Requirements 8116 TFTP Client Download Procedure 8118 TFTP Server Download Procedure Appendix B System Defaults Table B-1 System Default Values Page Appendix C Command Line Reference Table C-1 Console Commands Table C-2 System Commands Table C-3 IP Commands Table C-4 SNMP Commands Table C-5 Switching Database Commands Table C-6 Virtual LAN Commands Table C-7 Port Conguration Commands Table C-8 Switching Statistics Commands Table C-9 Spanning Tree Commands