Using an Snmp Manager | Allied Telesis at-8116 specs

Chapter 15

Using an SNMP Manager

This chapter contains instructions for the conﬁguration and management of the AT-8116 SNMP Management System.

Configuring the AT-8116 SNMP Agent

Global Setup

Once connected to the network and powered ON, the AT-8116 starts operating according to factory-set default values. However, to ensure proper operation and maximum performance speciﬁc to your network conﬁguration and to provide SNMP access, some environment-speciﬁc parameters must be conﬁgured through the Command Line Interface.

If you are conﬁguring the switch for the ﬁrst time:

1.Connect a terminal to the RS-232 connector.

2.Log in to the Command Line Interface.

3.Initialize all the AT-8116 parameters to their default values (see Table 1, System Default Values). Use the following command sequence:

init-nvram (deletes all current NVRAM configrations) warm-reset (loads the NVRAM configuration)

4.Wait until you see the LOGIN prompt again. Login to the CLI. Now all system parameters have been initialized to their default values.

15-1

Image 73

Allied Telesis at-8116 manual Using an Snmp Manager, Configuring the AT-8116 Snmp Agent

Contents

E R ’ S G U I D E Page Table of Contents Appendix B Rmon Administrative Interface Administrative Interface Network Management Systems Accessing the Snmp AgentSystem Requirements Software Requirements VT100 Terminal Settings Accessing the Command Line Interface Remotely Testing the InstallationPage Features of the Command Line Interface Command Line Interface SYSconsole pin Command pin not found Entering CommandsGet-comm read write Get-comm read Get-comm write SYSconsole ping 129.1.1.7 ? ping IP traffic generator System Commands System CommandsSYSconsolesystem SYSconsoleget-c? Command get-c not found Command Line Interface Structure2Commands Matching get-c SYSconsole? Commands Groups Help-kbd Console CommandsSYSconsolehelp-kbd Console Function Keys Banner LoginClear Logout Set-attr-msg Set-attr-promptSet-attr-text Set-passwd Console Commands Sys-stat System Commands SYSconsole System Commands Cold-reset Warm-resetGet-stst-level Set-stst-level level Get-sw-file Init-nvramSet-sw-file Get-tftp-srvr Set-fg-param Sw-dnldStart-fg Stop-fg Get-ip IP CommandsSet-ip Set-ipIPaddress Get-ip-cfg If no IP Config. is definedSet-ip-cfg Set-ip-cfg IPaddress netmask broadcast Clear-ip-cfg Get-gatew SYSconsoleget-gatew Default gateway address isSet-gatew Set-gatew IPaddress Get-arp-tbl Address Resolution CommandsDel-arp-entry SYSconsoleget-arp-tbl IfIndex IpAddress 194.090.136.126 Add-arp-entry Ping Ping CommandsPing-stop SYSconsoleping 194.90.136.23 Echo Requests SYSconsoleping 194.90.136.20Echo Responses Ping process press CR for prompt SYSconsole Ping-stop Stop the active ping Process Echo responses Ping process pressPage Snmp Community String Commands Snmp CommandsGet-comm Get-comm readwrite Set-comm Snmp Trap Message CommandsGet-auth Set-auth Add-trap Get-traps Get-rmon-state Del-trapSYSconsoledel-trap SYSconsoleget-rmon-state Lock Switching Database Commands Get-lt-entry Learning Table SYStelnetget-lt-16 Get-lt-16 SYStelnetﬁnd-lt-addr 0060e8112265 Find-lt-addr SYSconsolefind-lt-addr Del-lt-entryMAC Address 01-02-03-04-05-06 not in LT Del-lt-entry index Add-lt-entry Del-lt-addrGet-lt-age SYSconsoledel-lt-entry Set-lt-age runnvramall agingtime Set-lt-ageSYSconsoleset-lt-age all Page Type vlan to view the related commands SYSconsolevlan Virtual LAN Commands Get-con-matrix Virtual Broadcast Domains VBC ========================== SYSconsoleget-con-matrix Set-vbc-domain Set-vbc-domain runnvramall portlist Del-vbc-domainSet-vbc-domain all Del-vbc-domain runnvram domainid SYSconsoleget-vbc-matrix Get-vbc-matrix Set-sec-vlan Security VLANsSvlan Groups LANs 0 0 0 0 0 0 0 1 1 1 1 1 1 Del-sec-vlan3 4 5 6 7 8 9 0 1 Del-sec-vlan runnvram lanid Get-svlan-tbl runnvram Get-svlan-tblSYSconsoleget-svlan-tbl run + + + + + + + + SYSconsole Get-svlan-matrix runnvram SYSconsoleget-svlan-matrix run Get-svlan-matrixPage Set-mon-port Port Monitoring CommandsStop-mon Get-nv-mon Clear-nv-mon Save-mon Get-port-cfg Port Conﬁguration CommandsSYSconsoleget-port-cfg Set-port-dplex portnumber halffull Set-port-dplexSYSconsoleset-port-dplex 2 full Set-port-state Set-speed-selSet-aggr-mode SYSconsoleset-aggr-modePage Clr-cnt Switching Statistics CommandsGet-eth-cnt Switching Statistics Commands Get-rmon-cnt Get-colls-cntGet-sdist-cnt SYSconsoleget-colls-cnt ============================================= Get-mgm-brcnt15637 1123754 Set-stp enabledisable Spanning Tree CommandsGet-stp Set-stp Get-st-pcfg Get-st-bcfgGet-st-syscfg Set-br-prio Set-prt-enb Set-prt-prioSet-prt-pcost Page Configuring the AT-8116 Snmp Agent Using an Snmp Manager SYSconsoleset-gatew New read community Read publicPage Software Troubleshooting Page Software Downloading Tftp Client Download ProcedureRequirements Tftp Server Download Procedure System Default Values System DefaultsPage Table C-1 Console Commands Command Line Reference Table C-2 System Commands Table C-4SNMP Commands Table C-3IP Commands Table C-6 Virtual LAN Commands Table C-5 Switching Database Commands Table C-8Switching Statistics Commands Table C-7Port Conﬁguration CommandsTable C-9Spanning Tree Commands