Spanning Tree Commands, Get-stp, Set-stp | Allied Telesis at-8116

Chapter 14

Spanning Tree Commands

Spanning Tree automatically conﬁgures a loop-free topology in a bridged environment. However, note that the bridge on this switch is not VLAN-based and only one spanning tree is allowed regardless of the number of VLANs. The Spanning Tree agent is implemented in conformance to the IEEE 802.1d standard. Once spannning tree is enabled, it remains enabled even through resets or start ups.

Listed below are the conﬁguration commands pertinent to the operation of the Spanning Tree algorithm. Type <sp-tree> to view all the related commands. For spanning tree defaults, see Appendix B, “System Defaults”.

get-stp

Retrieve the current state of Spanning Tree. Options are enable or disable.

Note

The default state is disabled for spanning tree.

set-stp

This command enables or disables the Spanning Tree protocol.

Spanning Tree is enabled by default, in accordance with 802.1d.

Enabling or disabling Spanning Tree will not take effect until the

SNMP agent is reset, via warm-reset, cold-reset or a power cycle.

set-stp {enabledisable}

14-1

Image 69

Allied Telesis at-8116 manual Spanning Tree Commands, Get-stp, Set-stp enabledisable

Contents

E R ’ S G U I D E Page Table of Contents Appendix B Rmon Administrative Interface Administrative Interface Accessing the Snmp Agent Network Management SystemsSystem Requirements Software Requirements VT100 Terminal Settings Accessing the Command Line Interface Remotely Testing the InstallationPage Features of the Command Line Interface Command Line Interface SYSconsole pin Command pin not found Entering CommandsGet-comm read write Get-comm read Get-comm write SYSconsole ping 129.1.1.7 ? ping IP traffic generator System Commands System CommandsSYSconsolesystem Command Line Interface Structure SYSconsoleget-c? Command get-c not found2Commands Matching get-c SYSconsole? Commands Groups Help-kbd Console CommandsSYSconsolehelp-kbd Console Function Keys Banner LoginClear Logout Set-attr-msg Set-attr-promptSet-attr-text Set-passwd Console Commands Sys-stat System Commands SYSconsole System Commands Cold-reset Warm-resetGet-stst-level Set-stst-level level Get-sw-file Init-nvramSet-sw-file Get-tftp-srvr Sw-dnld Set-fg-paramStart-fg Stop-fg Get-ip IP CommandsSet-ip Set-ipIPaddress Get-ip-cfg If no IP Config. is definedSet-ip-cfg Set-ip-cfg IPaddress netmask broadcast Clear-ip-cfg Get-gatew SYSconsoleget-gatew Default gateway address isSet-gatew Set-gatew IPaddress Get-arp-tbl Address Resolution CommandsDel-arp-entry SYSconsoleget-arp-tbl IfIndex IpAddress 194.090.136.126 Add-arp-entry Ping Ping CommandsPing-stop SYSconsoleping 194.90.136.23 SYSconsoleping 194.90.136.20 Echo RequestsEcho Responses Ping process press CR for prompt SYSconsole Ping-stop Stop the active ping Process Echo responses Ping process pressPage Snmp Community String Commands Snmp CommandsGet-comm Get-comm readwrite Set-comm Snmp Trap Message CommandsGet-auth Set-auth Add-trap Get-traps Get-rmon-state Del-trapSYSconsoledel-trap SYSconsoleget-rmon-state Lock Switching Database Commands Get-lt-entry Learning Table SYStelnetget-lt-16 Get-lt-16 SYStelnetﬁnd-lt-addr 0060e8112265 Find-lt-addr SYSconsolefind-lt-addr Del-lt-entryMAC Address 01-02-03-04-05-06 not in LT Del-lt-entry index Add-lt-entry Del-lt-addrGet-lt-age SYSconsoledel-lt-entry Set-lt-age Set-lt-age runnvramall agingtimeSYSconsoleset-lt-age all Page Type vlan to view the related commands SYSconsolevlan Virtual LAN Commands Get-con-matrix Virtual Broadcast Domains VBC ========================== SYSconsoleget-con-matrix Set-vbc-domain Set-vbc-domain runnvramall portlist Del-vbc-domainSet-vbc-domain all Del-vbc-domain runnvram domainid SYSconsoleget-vbc-matrix Get-vbc-matrix Security VLANs Set-sec-vlanSvlan Groups LANs 0 0 0 0 0 0 0 1 1 1 1 1 1 Del-sec-vlan3 4 5 6 7 8 9 0 1 Del-sec-vlan runnvram lanid Get-svlan-tbl runnvram Get-svlan-tblSYSconsoleget-svlan-tbl run + + + + + + + + SYSconsole Get-svlan-matrix runnvram SYSconsoleget-svlan-matrix run Get-svlan-matrixPage Set-mon-port Port Monitoring CommandsStop-mon Get-nv-mon Clear-nv-mon Save-mon Port Conﬁguration Commands Get-port-cfgSYSconsoleget-port-cfg Set-port-dplex Set-port-dplex portnumber halffullSYSconsoleset-port-dplex 2 full Set-port-state Set-speed-selSet-aggr-mode SYSconsoleset-aggr-modePage Switching Statistics Commands Clr-cntGet-eth-cnt Switching Statistics Commands Get-rmon-cnt Get-colls-cntGet-sdist-cnt SYSconsoleget-colls-cnt Get-mgm-brcnt =============================================15637 1123754 Set-stp enabledisable Spanning Tree CommandsGet-stp Set-stp Get-st-pcfg Get-st-bcfgGet-st-syscfg Set-br-prio Set-prt-prio Set-prt-enbSet-prt-pcost Page Configuring the AT-8116 Snmp Agent Using an Snmp Manager SYSconsoleset-gatew New read community Read publicPage Software Troubleshooting Page Tftp Client Download Procedure Software DownloadingRequirements Tftp Server Download Procedure System Default Values System DefaultsPage Table C-1 Console Commands Command Line Reference Table C-2 System Commands Table C-4SNMP Commands Table C-3IP Commands Table C-6 Virtual LAN Commands Table C-5 Switching Database Commands Table C-7Port Conﬁguration Commands Table C-8Switching Statistics CommandsTable C-9Spanning Tree Commands