Recommended Installation Tools | Asante Technologies 3500 Series

2.1.2 Recommended Installation Tools

You will need the following tools and equipment (not included) to install the switch into an equipment rack:

• Flat head screwdriver

• Phillips head screwdriver

• Antistatic mat or foam

2.1.3 Power Requirements

The electrical outlet should be located near the switch and be easily accessible. It must also be properly grounded.

Make sure the power source adheres to the following guidelines:

•Power: Auto Switching 110/240 VAC

•Frequency range: 50/60 Hz

•Maximum Input AC Current: 1.0A at 115 VAC full load

2.1.4 Environmental Requirements

The switch must be installed in a clean, dry, dust-free area with adequate air circulation to maintain the following environmental limits:

•Operating Temperature: 0° to 40° C (32° to 104° F)

•Storage Temperature: -20° to 70° C (-4° to 158° F)

•Relative Humidity: 10% to 90% non-condensing

•Storage Relative Humidity: 10% to 95% non-condensing

Avoid direct sunlight, heat sources, or areas with high levels of electromagnetic interference.

2.1.5 Cooling and Airflow

The IntraCore 3500 series switches use internal fans for air-cooling. Do not restrict airflow by covering or obstructing air vents on the sides of the switch.

2.2 Installation into an Equipment Rack

To install the unit in an equipment rack, use the following procedure:

Important! Before continuing, disconnect all cables from the unit.

1.Place the switch on a flat, stable surface.

2.Locate a rack-mounting bracket (supplied) and place it over the mounting holes on one side of the unit.

3.Use the screws (supplied) to secure the bracket (with a Phillips screwdriver).

4.Repeat the two previous steps on the other side of the unit.

5.Place the switch in the equipment rack.

6.Secure the switch by securing its mounting brackets onto the equipment rack with the appropriate screws (supplied).

Important! Make sure the unit is supported until all the mounting screws for each bracket are secured to the equipment rack. Failure to do so could cause the unit to fall, which may result in personal injury or damage to the unit.

13

Image 13

Asante Technologies 3500 Series Installation into an Equipment Rack, Recommended Installation Tools, Power Requirements

Contents

IntraCore 3500 Series Quick Start Guide IntraCore 3500 Series Gigabit Ethernet Switches User’s Manual Table of Contents Page Introduction Package Contents 1 IC3524 Models LEDs 4810/100 2 IC3548-2GT #49 Front and Back Panel Descriptions Management and Configuration Web-Based Interface Console InterfaceSnmp Management Installation Overview Hardware Installation and SetupSafety Overview Recommended Installation Tools Installation into an Equipment RackPower Requirements Environmental Requirements Gbic Interfaces Installing a GbicEquipment Rack Guidelines Connecting Power Installing Optional Hardware ModulesRemoving a Gbic Gbic Care and Handling 1 10/100BaseT Ports Cabling Procedures Connecting to the Network Gigabit Ethernet Ports Cabling Procedures SetupConnecting to a Console Connecting Via the Web Browser Changing the PasswordConnecting Via Telnet Snmp Management IP Assignment Using the Stacking Feature IC3524 only Toggle Stacking Enable/Disable Accessing a Submenu ConfigurationLogging General Information Configuration MenuExiting a Submenu Changing System Administration Info System Administration Configuration Bootstrap Configuration System IP ConfigurationChanging System IP Information Changing Community Strings Snmp Configuration Adding or Updating a Trap Receiver Enabling Authentication TrapsDeleting a Trap Receiver Basic Port Configuration Menu appears Port Configuration Enabling or Disabling a Port Configuring Auto-Negotiation Configuring 1000BaseX Ports Configuring a Port ManuallyToggling Port Link Speed Toggling Half to Full Duplex Setting Port Class of Service Advanced Port ConfigurationEnabling or Disabling 802.3x Flow Control Global Port Configuration Setting Port Default Priority Displaying the Forwarding Database Unicast Forwarding Database Configuration Searching for a MAC Address Setting the MAC Address Age-Out Time Security Management Port Mirroring ConfigurationVlan Management IP Multicast Traffic Management Setting the Monitor Port File Up/Downloading ConfigurationImage Downloading through Tftp Performing a Software Upgrade at Runtime Serial Downloading Configuration Resetting the Switch System Reset ConfigurationPerforming a Software Upgrade System Log Scheduling a System Reset Clearing the System Log User Interface Configuration Setting Telnet Idle Time-out Period Setting Console Idle Time-out Period System Utility Changing the PasswordEnabling or Disabling the Web Server Viewing Statistics Advanced Management Configuring Spanning Tree ParametersSpanning Tree Protocol Enabling and Disabling STP Setting Port Priority and Path Cost Spanning Tree Port Configuration Duplicated IP Detection and Trap Snmp and Rmon ManagementRmon Management Enabling and Disabling Duplicated IP Detection Enabling and Disabling Station Movement TrapEnabling and Disabling Duplicated IP Trap Viewing a List of Duplicated IP Addresses Configuring Port New Node Detection Trap Configuring Port Security Configuring Security Level 2 or Level Configuring Port Lock and Intruder LockSetting the Intruder Trap Resetting Security to Defaults Vlan Specifications for the IntraCore 3500 SeriesOther Vlan Features of the switch Inserting/Modifying a Port Trusted MAC Address Kkxxxxxx Kxxxxxxx Configuring Static Vlan Groups Advanced Static Vlan Configuration Setting the Port Vlan ID Configuring Vlan Port AttributesSpecifying Tagging or No Tagging for a Port Displaying a Summary of Vlan Groups Configuring Port Receive Frame TypeDisplaying a Vlan Port Summary Adding and Deleting VLANs from the Port Multicast Addresses Resetting Vlan Configuration to Defaults Igmp Snooping Configuring IP Multicast Traffic ManagementEnabling and Disabling Igmp Snooping Displaying a Summary of Group Addresses Adding Ports to the Selected Address IP Multicast Forwarding Database ConfigurationInserting a Multicast Group Address Removing a Multicast Group Address To remove an address Web-Based Management Accessing with a Web Browser Genl Info General Information Button Front Panel Button Statistics Button Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp Button Vlan Button Port Configuration Creating or Modifying a Vlan Vlan ConfigurationAdding and Deleting Port Members Page Security Button Duplicate IP Button Snmp Management Operations Snmp ManagementSnmp Protocol MIB Tree Community Name and SecurityName Space Path MIB Groups SupportedPage VLANs Switching ConceptsPort-Based VLANs Vlan ID and Tagged Frames How It Works Port Vlan IDSpanning Tree Parameters Full Duplex, Flow Control and Auto-negotiation Forward DelayFull Duplex Port Priority Auto-Negotiation Flow Control Problem Possible Solutions Appendix A. Troubleshooting Features Appendix B. Features and SpecificationsSpecifications Technical Support and Warranty Physical CharacteristicsEnvironmental Range Standards Compliance FCC Compliance Statement Important Safety Instructions Appendix C. FCC Compliance and Warranty StatementsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal Name Appendix E. Online Warranty Registration Bootstrap Configuration Appendix F. BootP ConfigurationImage Banks Loading Software Locally