Sensor manufacturer’s instructions, Mount the backplate | AT&T 8000

STEP 18

Mount the Transmitters

Mount Wireless Remote/Transmitter	1.	Mount the sensor to be used with the transmitter. (Follow
		the sensor manufacturer’s instructions.)

2.Thread sensor wires through the Wireless Remote/Transmitter

backplate.

Too much wire can cause the housing to seat improperly and cause false alarms.

3.Mount the backplate.

Be careful not to over-tighten the backplate screws. False alarms may result because the housing seats improperly against the tamper switch.

AT&T Proprietary Information

2-64

Image 65

AT&T 8000 Mount the Transmitters Mount Wireless Remote/Transmitter, Sensor manufacturer’s instructions

Contents

Pursuant to Company Instructions AT&T Security System Exceeding those expectations is what AT&T is all about Service is all aboutSystem Knowledgc Good Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Obtain the floor plan and component list/work order Chart to help determine what you need. OutlineWhich are part of the AT&T Security Survey Call the customer to verify the time and location Phillips-Head Screwdriver Common Hand Tools Slotted-Head Screwdriver Requirements WiringEnvironment Page Salesman has told him/her Meet the Customer Confirm Correct LocationYou can answer any questions before you leave Look for broken windows, scratched paint, torn wallpaper Paper mills Choose Central Controller Location PrecautionsLarge neighborhood antennas MetaI kitchen or bathroom cupboards ObjectsRefrigerators MetaI sinks and tubs Keypad Transmitter ISI Wireless Siren Controller Wireless Remote Transmitter Transmitter locations Antenna PlacementAntenna length less than I5 feet, if possible Them Possible Antenna Run in a Multi-level Home Transformer Wire lath in plaster walls Signal must pass through several outer wallsProblems, especially in L shaped homes Insulation House code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Environmental17 Install the Digital Communicator Possible. Sharp angles in the wiring run reduce Problem. Reset the watchdog with the AT&T ModelProgram the Digital Communicator using the AT&T Remote Programming Package It is critical that you identify Run the Central Controller Antenna Choose the antenna runSources of possible RF interference Potential blocks to RF waves Plug in the Transformer Verify power Power Up the Central Controller Digital display Enter the Installer Test Mode Allow at least two inches between the unit and the ceiling Choose Transmitter Mounting LocationsKeypad Transmitter Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Alarm Hour Sensor Loop Not Secure Wireless Remote/TransmitterBattery is OK CONDITlON Sensor Locate the phone line protector block Run the Phone Line for the Digital Communicator Step LYll Requires more powcr than 450 MA Then install the High Power SirenRelay Module Recheck All Transmitter Locations Program the Transmitters Beeps and alarms to specific transmitters. Code numbersLet’s look at the I.D. Code for a moment Number is used by the Central Controller to relay trouble 1171 Wireless Remote/Transmitter DIP Switches Selectable sensor loop zone House code settingProgramming Selectable sensor loop option = closed loop Set House Code/Option DIP Switches= high security = low securityPage Yellow Wire Third Number 1st = B 2nd = W White WirePage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Press up on the tab at the bottom Housing Intrusion Audible Panic Interior Environmental Auxiliary AT&T Proprietary Information Transmitter PIR T Lens Replace lens brackets carefully AT&T Proprietary Information Active Post on Pirt Circuit Board PscH8$EPage Open the detector front housing Use the information presented in the InstallationAccessed through a small hole in the backplate Set the House code DIP switches $t.ns~ Switch Page Mount the backplate Mount the Transmitters Mount Wireless Remote/TransmitterSensor manufacturer’s instructions USE Jumpers To Close Loops For Handheld USE Mount Keypad Transmitter Attach the front housing Mount Universal Transmitter Page Auxiliary APPLlCATlONS Panic APPLlCATiONS Comes on when you move Reduce the sensitivity of the Pirt by usingSeveral minutes to stabilize Walk test the Pirt to verify its coverage Exit the Installer Test Mode Choose the Wireless Siren /Controller On = Silent OFF = Sound Switch 9 should Always be onSources of possible RF interference Potential blocks to RF waves Screw provided #6-32 Verify that the AC Power Light is onTransformer Plug in the transformer Until 1 Beep is heard Perform the System Test System Test Hardwired System Test 24-Hour Zone Transmitters RF Scanner