Several minutes to stabilize, Only | AT&T 8000 instruction

Mount Passive Infrared Transmitter 1.	Mount the PIRT backpiate with #6 screws. For a corner
(PIRT)	mount, use the mounting guides on the angled sides of the
	backplate.
2.	Attach the front housing to the backplate. Allow the unit
	several minutes to stabilize.
3.	Walk test the PIRT to verify its coverage.
	a.	Reduce the sensitivity of the PIRT by using the
		sensitivity adjustment knob on the circuit board.
		(8560 only)
		Turn the knob counterclockwise. (8560 only)
	b.	Walk in several different paths across the detection
		area. (For 8561 there is no sensitivity adjustment)
	c.	Listen for the proper number of indication beeps.
	d.	Watch to see that the reh walk-test LED light
		comes on when you move.
	e.	Check to see that the walk-test LED doesn’t light
		when you stand out of range of the detection zone.
	f.	Adjust the sensitivity up as necessary. (8560 only)

4.Park the LED.

a.Disconnect the LED plug from the "Active” post on the PlRT circuit board.

b.Connect the LED plug to the "Park" post.

5.Deactivate the walk test by moving DIP switch 7 to the ON position.

NOTE: Failure to disable the walk-test LED and set switch X7 to "on" will shorten battery life.

AT&T Proprietary Information

2-70

Image 71

AT&T 8000 Several minutes to stabilize, Walk test the Pirt to verify its coverage, Only, Comes on when you move

Contents

Pursuant to Company Instructions AT&T Security System Knowledgc Service is all aboutExceeding those expectations is what AT&T is all about System Good Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Call the customer to verify the time and location Chart to help determine what you need. OutlineObtain the floor plan and component list/work order Which are part of the AT&T Security Survey Phillips-Head Screwdriver Common Hand Tools Slotted-Head Screwdriver Requirements WiringEnvironment Page Look for broken windows, scratched paint, torn wallpaper Meet the Customer Confirm Correct LocationSalesman has told him/her You can answer any questions before you leave Paper mills Choose Central Controller Location PrecautionsLarge neighborhood antennas MetaI sinks and tubs ObjectsMetaI kitchen or bathroom cupboards Refrigerators Keypad Transmitter ISI Wireless Siren Controller Wireless Remote Transmitter Them Antenna PlacementTransmitter locations Antenna length less than I5 feet, if possible Possible Antenna Run in a Multi-level Home Transformer Insulation Signal must pass through several outer wallsWire lath in plaster walls Problems, especially in L shaped homes House code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Environmental17 Install the Digital Communicator Remote Programming Package Problem. Reset the watchdog with the AT&T ModelPossible. Sharp angles in the wiring run reduce Program the Digital Communicator using the AT&T Potential blocks to RF waves Run the Central Controller Antenna Choose the antenna runIt is critical that you identify Sources of possible RF interference Plug in the Transformer Verify power Power Up the Central Controller Digital display Enter the Installer Test Mode Allow at least two inches between the unit and the ceiling Choose Transmitter Mounting LocationsKeypad Transmitter Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation CONDITlON Wireless Remote/TransmitterAlarm Hour Sensor Loop Not Secure Battery is OK Sensor Locate the phone line protector block Run the Phone Line for the Digital Communicator Step LYll Recheck All Transmitter Locations Then install the High Power SirenRequires more powcr than 450 MA Relay Module Number is used by the Central Controller to relay trouble Beeps and alarms to specific transmitters. Code numbersProgram the Transmitters Let’s look at the I.D. Code for a moment 1171 Selectable sensor loop option Selectable sensor loop zone House code settingWireless Remote/Transmitter DIP Switches Programming = low security Set House Code/Option DIP Switches= closed loop = high securityPage Yellow Wire Third Number 1st = B 2nd = W White WirePage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Press up on the tab at the bottom Housing Intrusion Audible Panic Interior Environmental Auxiliary AT&T Proprietary Information Transmitter PIR T Lens Replace lens brackets carefully AT&T Proprietary Information Active Post on Pirt Circuit Board PscH8$EPage Set the House code DIP switches Use the information presented in the InstallationOpen the detector front housing Accessed through a small hole in the backplate $t.ns~ Switch Page Mount the backplate Mount the Transmitters Mount Wireless Remote/TransmitterSensor manufacturer’s instructions USE Jumpers To Close Loops For Handheld USE Mount Keypad Transmitter Attach the front housing Mount Universal Transmitter Page Auxiliary APPLlCATlONS Panic APPLlCATiONS Walk test the Pirt to verify its coverage Reduce the sensitivity of the Pirt by usingComes on when you move Several minutes to stabilize Exit the Installer Test Mode Potential blocks to RF waves On = Silent OFF = Sound Switch 9 should Always be onChoose the Wireless Siren /Controller Sources of possible RF interference Screw provided #6-32 Verify that the AC Power Light is onTransformer Plug in the transformer Until 1 Beep is heard Perform the System Test System Test Hardwired System Test 24-Hour Zone Transmitters RF Scanner