Power Up the Central Controller | AT&T 8000 specification

STEP 9

Power Up the Central Controller

Attach the Central Controllet antenna to the transfomer

Plug in the Transformer

Verify power

CAUTION: BEFORE YOU POWER UP, PROGRAM AT LEAST ONE WIRELESS REMOTE/TRANSMITTER SO YOU CAN IMMEDIATELY ENTER THE INSTALLER TEST MODE.

Use only a 16 VAC transformer, Comcode number 845402734.

Plug the transformer into the 120 VAC, 60 Hz, wall outlet and secure to the waII using the 6-32 screw provided.

CAUTION: The transformer is fused, so be careful not to short’ the leads.

NOTE: Do not plug the transformer into an outlet that is controlled by a waII switch.

Verify that the Central Controller is receiving AC power by checking to see that:

. The AC Power LED is on.

.	Two dashes (- -) appear in the digital display.

AT&T Proprietary Information 2-26

Image 27

AT&T 8000 installation instructions Power Up the Central Controller, Plug in the Transformer Verify power

Contents

Pursuant to Company Instructions AT&T Security System Knowledgc Service is all aboutExceeding those expectations is what AT&T is all about System Good Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Call the customer to verify the time and location Chart to help determine what you need. OutlineObtain the floor plan and component list/work order Which are part of the AT&T Security Survey Phillips-Head Screwdriver Common Hand Tools Slotted-Head Screwdriver Wiring EnvironmentRequirements Page Look for broken windows, scratched paint, torn wallpaper Meet the Customer Confirm Correct LocationSalesman has told him/her You can answer any questions before you leave Choose Central Controller Location Precautions Large neighborhood antennasPaper mills MetaI sinks and tubs ObjectsMetaI kitchen or bathroom cupboards Refrigerators Keypad Transmitter ISI Wireless Siren Controller Wireless Remote Transmitter Them Antenna PlacementTransmitter locations Antenna length less than I5 feet, if possible Possible Antenna Run in a Multi-level Home Transformer Insulation Signal must pass through several outer wallsWire lath in plaster walls Problems, especially in L shaped homes House code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Environmental17 Install the Digital Communicator Remote Programming Package Problem. Reset the watchdog with the AT&T ModelPossible. Sharp angles in the wiring run reduce Program the Digital Communicator using the AT&T Potential blocks to RF waves Run the Central Controller Antenna Choose the antenna runIt is critical that you identify Sources of possible RF interference Plug in the Transformer Verify power Power Up the Central Controller Digital display Enter the Installer Test Mode Choose Transmitter Mounting Locations Keypad TransmitterAllow at least two inches between the unit and the ceiling Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation CONDITlON Wireless Remote/TransmitterAlarm Hour Sensor Loop Not Secure Battery is OK Sensor Locate the phone line protector block Run the Phone Line for the Digital Communicator Step LYll Recheck All Transmitter Locations Then install the High Power SirenRequires more powcr than 450 MA Relay Module Number is used by the Central Controller to relay trouble Beeps and alarms to specific transmitters. Code numbersProgram the Transmitters Let’s look at the I.D. Code for a moment 1171 Selectable sensor loop option Selectable sensor loop zone House code settingWireless Remote/Transmitter DIP Switches Programming = low security Set House Code/Option DIP Switches= closed loop = high securityPage Yellow Wire Third Number 1st = B 2nd = W White WirePage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Press up on the tab at the bottom Housing Intrusion Audible Panic Interior Environmental Auxiliary AT&T Proprietary Information Transmitter PIR T Lens Replace lens brackets carefully AT&T Proprietary Information Active Post on Pirt Circuit Board PscH8$EPage Set the House code DIP switches Use the information presented in the InstallationOpen the detector front housing Accessed through a small hole in the backplate $t.ns~ Switch Page Mount the Transmitters Mount Wireless Remote/Transmitter Sensor manufacturer’s instructionsMount the backplate USE Jumpers To Close Loops For Handheld USE Mount Keypad Transmitter Attach the front housing Mount Universal Transmitter Page Auxiliary APPLlCATlONS Panic APPLlCATiONS Walk test the Pirt to verify its coverage Reduce the sensitivity of the Pirt by usingComes on when you move Several minutes to stabilize Exit the Installer Test Mode Potential blocks to RF waves On = Silent OFF = Sound Switch 9 should Always be onChoose the Wireless Siren /Controller Sources of possible RF interference Verify that the AC Power Light is on Transformer Plug in the transformerScrew provided #6-32 Until 1 Beep is heard Perform the System Test System Test Hardwired System Test 24-Hour Zone Transmitters RF Scanner