Wiring, Environment, Requirements | AT&T 8000 specs

INSTALLATION INFORMATION

GENERAL INFORMATION
Wiring	Use #22 AWG minimum for sensor wiring and digital
	communicator channels. Use #18 AWG minimum for AC power.
	All wire should be UL-listed
Environment	The system is designed to work in an indoor heated environment
	(40 to 120 degrees F.) Battery life may be significantly reduced if
	components are in direct sunlight or in an unheated location.
U.L. Requirements	UL requires that any fire application includes either a Supervised
	Smoke Detector Transmitter or a Universal Transmitter
	configured for fire and connected to a UL-listed single station
	smoke detector with relay. Other types of smoke/fire sensors
	(suck as heat sensors) may be included in the system.
	The Universal Transmitter sbould be used in its supervised mode
	unless it is being used as a portable device.
	If the internal sounder on the Central controller or Wireless
	Siren/controller is silenced for intrusion alarms (DIP switch
	option) there should be an auxiliary sounding device in the system.
	The Wheelock EH-EL2 series electronic horn should be used as a
	siren or horn interface.
	Open loop sensor connections at any transmitter or Central
	Controller should be less 3 feet in length with no barriers in
	between, and the sensor shall be provided with a test feature.
	All sensors should be UL-listed.

AT&T Proprietary Information 2-7

Image 8

AT&T 8000 installation instructions Wiring, Environment, Requirements

Contents

AT&T Security System Pursuant to Company Instructions Service is all about Exceeding those expectations is what AT&T is all aboutSystem Knowledgc Good Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Chart to help determine what you need. Outline Obtain the floor plan and component list/work orderWhich are part of the AT&T Security Survey Call the customer to verify the time and location Common Hand Tools Slotted-Head Screwdriver Phillips-Head Screwdriver Requirements WiringEnvironment Page Meet the Customer Confirm Correct Location Salesman has told him/herYou can answer any questions before you leave Look for broken windows, scratched paint, torn wallpaper Paper mills Choose Central Controller Location PrecautionsLarge neighborhood antennas Objects MetaI kitchen or bathroom cupboardsRefrigerators MetaI sinks and tubs Wireless Remote Transmitter Keypad Transmitter ISI Wireless Siren Controller Antenna Placement Transmitter locationsAntenna length less than I5 feet, if possible Them Possible Antenna Run in a Multi-level Home Transformer Signal must pass through several outer walls Wire lath in plaster wallsProblems, especially in L shaped homes Insulation House code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Install the Digital Communicator Environmental17 Problem. Reset the watchdog with the AT&T Model Possible. Sharp angles in the wiring run reduceProgram the Digital Communicator using the AT&T Remote Programming Package Run the Central Controller Antenna Choose the antenna run It is critical that you identifySources of possible RF interference Potential blocks to RF waves Power Up the Central Controller Plug in the Transformer Verify power Enter the Installer Test Mode Digital display Allow at least two inches between the unit and the ceiling Choose Transmitter Mounting LocationsKeypad Transmitter Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Wireless Remote/Transmitter Alarm Hour Sensor Loop Not SecureBattery is OK CONDITlON Sensor Run the Phone Line for the Digital Communicator Locate the phone line protector block Step LYll Then install the High Power Siren Requires more powcr than 450 MARelay Module Recheck All Transmitter Locations Beeps and alarms to specific transmitters. Code numbers Program the TransmittersLet’s look at the I.D. Code for a moment Number is used by the Central Controller to relay trouble 1171 Selectable sensor loop zone House code setting Wireless Remote/Transmitter DIP SwitchesProgramming Selectable sensor loop option Set House Code/Option DIP Switches = closed loop= high security = low securityPage White Wire Yellow Wire Third Number 1st = B 2nd = WPage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Housing Press up on the tab at the bottom Intrusion Audible Panic Interior Auxiliary Environmental AT&T Proprietary Information Lens Replace lens brackets carefully Transmitter PIR T AT&T Proprietary Information PscH8$E Active Post on Pirt Circuit BoardPage Use the information presented in the Installation Open the detector front housingAccessed through a small hole in the backplate Set the House code DIP switches $t.ns~ Switch Page Mount the backplate Mount the Transmitters Mount Wireless Remote/TransmitterSensor manufacturer’s instructions USE Jumpers To Close Loops For Handheld USE Attach the front housing Mount Keypad Transmitter Mount Universal Transmitter Page Panic APPLlCATiONS Auxiliary APPLlCATlONS Reduce the sensitivity of the Pirt by using Comes on when you moveSeveral minutes to stabilize Walk test the Pirt to verify its coverage Exit the Installer Test Mode On = Silent OFF = Sound Switch 9 should Always be on Choose the Wireless Siren /ControllerSources of possible RF interference Potential blocks to RF waves Screw provided #6-32 Verify that the AC Power Light is onTransformer Plug in the transformer Until 1 Beep is heard System Test Hardwired Perform the System Test System Test 24-Hour Zone Transmitters RF Scanner