Use the information presented in the Installation | AT&T 8000

Prepare the Supervised Smoke	1.	Verify the proper location for the Supervised Smoke
Detector Transmitter		Detector Transmitter.
		Use the information presented in the Installation
		Information section to help determine the correct
		location.
	2.	Open the detector front housing.
		Use a screwdriver to bend the release tab that can be
		accessed through a small hole in the backplate.
	3.	Program the detector.
		. Set the House code DIP switches.
		. Set the I.D. DIP switches.

SMOKE DETECTOR

AT&T Proprietary information 241

Image 62

AT&T 8000 Use the information presented in the Installation, Open the detector front housing, Program the detector

Contents

AT&T Security System Pursuant to Company Instructions System Service is all aboutExceeding those expectations is what AT&T is all about Knowledgc Good Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Which are part of the AT&T Security Survey Chart to help determine what you need. OutlineObtain the floor plan and component list/work order Call the customer to verify the time and location Common Hand Tools Slotted-Head Screwdriver Phillips-Head Screwdriver Requirements WiringEnvironment Page You can answer any questions before you leave Meet the Customer Confirm Correct LocationSalesman has told him/her Look for broken windows, scratched paint, torn wallpaper Paper mills Choose Central Controller Location PrecautionsLarge neighborhood antennas Refrigerators ObjectsMetaI kitchen or bathroom cupboards MetaI sinks and tubs Wireless Remote Transmitter Keypad Transmitter ISI Wireless Siren Controller Antenna length less than I5 feet, if possible Antenna PlacementTransmitter locations Them Possible Antenna Run in a Multi-level Home Transformer Problems, especially in L shaped homes Signal must pass through several outer wallsWire lath in plaster walls Insulation House code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Install the Digital Communicator Environmental17 Program the Digital Communicator using the AT&T Problem. Reset the watchdog with the AT&T ModelPossible. Sharp angles in the wiring run reduce Remote Programming Package Sources of possible RF interference Run the Central Controller Antenna Choose the antenna runIt is critical that you identify Potential blocks to RF waves Power Up the Central Controller Plug in the Transformer Verify power Enter the Installer Test Mode Digital display Allow at least two inches between the unit and the ceiling Choose Transmitter Mounting LocationsKeypad Transmitter Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Battery is OK Wireless Remote/TransmitterAlarm Hour Sensor Loop Not Secure CONDITlON Sensor Run the Phone Line for the Digital Communicator Locate the phone line protector block Step LYll Relay Module Then install the High Power SirenRequires more powcr than 450 MA Recheck All Transmitter Locations Let’s look at the I.D. Code for a moment Beeps and alarms to specific transmitters. Code numbersProgram the Transmitters Number is used by the Central Controller to relay trouble 1171 Programming Selectable sensor loop zone House code settingWireless Remote/Transmitter DIP Switches Selectable sensor loop option = high security Set House Code/Option DIP Switches= closed loop = low securityPage White Wire Yellow Wire Third Number 1st = B 2nd = WPage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Housing Press up on the tab at the bottom Intrusion Audible Panic Interior Auxiliary Environmental AT&T Proprietary Information Lens Replace lens brackets carefully Transmitter PIR T AT&T Proprietary Information PscH8$E Active Post on Pirt Circuit BoardPage Accessed through a small hole in the backplate Use the information presented in the InstallationOpen the detector front housing Set the House code DIP switches $t.ns~ Switch Page Mount the backplate Mount the Transmitters Mount Wireless Remote/TransmitterSensor manufacturer’s instructions USE Jumpers To Close Loops For Handheld USE Attach the front housing Mount Keypad Transmitter Mount Universal Transmitter Page Panic APPLlCATiONS Auxiliary APPLlCATlONS Several minutes to stabilize Reduce the sensitivity of the Pirt by usingComes on when you move Walk test the Pirt to verify its coverage Exit the Installer Test Mode Sources of possible RF interference On = Silent OFF = Sound Switch 9 should Always be onChoose the Wireless Siren /Controller Potential blocks to RF waves Screw provided #6-32 Verify that the AC Power Light is onTransformer Plug in the transformer Until 1 Beep is heard System Test Hardwired Perform the System Test System Test 24-Hour Zone Transmitters RF Scanner