AT&T Proprietary Information | AT&T 8000 specification

3.Test the voltage of your 9-volt battery. Connect the battery. Check the current draw.

4.Log the transmitter location on the Central Controller Zone Locator Card.

5.Temporarily place the transmitter in the area that it will be mounted. Use double-sided tape, if necessary.

6.Perform the Universal Transmitter RF link test.

a. Use a pencil to press the Alarm/Test button.

b. Listen for the proper number of indication beeps from the Central Controller.

C. Check the Central Controller to verify that the proper transmitter ID number appears.

d. Check the status LEDs on the Central Controller for more information.

AT&T Proprietary Information

2-56

Image 57

AT&T 8000 installation instructions AT&T Proprietary Information

Contents

Pursuant to Company Instructions AT&T Security System Exceeding those expectations is what AT&T is all about Service is all aboutSystem Knowledgc Good Service Accountability Attitude Customer Contact Page AT&T Proprietary Information Obtain the floor plan and component list/work order Chart to help determine what you need. OutlineWhich are part of the AT&T Security Survey Call the customer to verify the time and location Phillips-Head Screwdriver Common Hand Tools Slotted-Head Screwdriver Wiring EnvironmentRequirements Page Salesman has told him/her Meet the Customer Confirm Correct LocationYou can answer any questions before you leave Look for broken windows, scratched paint, torn wallpaper Choose Central Controller Location Precautions Large neighborhood antennasPaper mills MetaI kitchen or bathroom cupboards ObjectsRefrigerators MetaI sinks and tubs Keypad Transmitter ISI Wireless Siren Controller Wireless Remote Transmitter Transmitter locations Antenna PlacementAntenna length less than I5 feet, if possible Them Possible Antenna Run in a Multi-level Home Transformer Wire lath in plaster walls Signal must pass through several outer wallsProblems, especially in L shaped homes Insulation House code USE Within a Half Mile Radius House Code DIP Switch Combinations House Code DIP Switch Combinations AT&T Proprietary Information Central Controller Terminal Strip Environmental17 Install the Digital Communicator Possible. Sharp angles in the wiring run reduce Problem. Reset the watchdog with the AT&T ModelProgram the Digital Communicator using the AT&T Remote Programming Package It is critical that you identify Run the Central Controller Antenna Choose the antenna runSources of possible RF interference Potential blocks to RF waves Plug in the Transformer Verify power Power Up the Central Controller Digital display Enter the Installer Test Mode Choose Transmitter Mounting Locations Keypad TransmitterAllow at least two inches between the unit and the ceiling Pirt Zone TOP View Curtain Lens Ssdt Installation Considerations Other Installation Considerations ‘t J Typical single floor installation Alarm Hour Sensor Loop Not Secure Wireless Remote/TransmitterBattery is OK CONDITlON Sensor Locate the phone line protector block Run the Phone Line for the Digital Communicator Step LYll Requires more powcr than 450 MA Then install the High Power SirenRelay Module Recheck All Transmitter Locations Program the Transmitters Beeps and alarms to specific transmitters. Code numbersLet’s look at the I.D. Code for a moment Number is used by the Central Controller to relay trouble 1171 Wireless Remote/Transmitter DIP Switches Selectable sensor loop zone House code settingProgramming Selectable sensor loop option = closed loop Set House Code/Option DIP Switches= high security = low securityPage Yellow Wire Third Number 1st = B 2nd = W White WirePage House code Transmitter ID Switch 8 should be set on for high security to Keypad Transmitter Initial Programming Page Press up on the tab at the bottom Housing Intrusion Audible Panic Interior Environmental Auxiliary AT&T Proprietary Information Transmitter PIR T Lens Replace lens brackets carefully AT&T Proprietary Information Active Post on Pirt Circuit Board PscH8$EPage Open the detector front housing Use the information presented in the InstallationAccessed through a small hole in the backplate Set the House code DIP switches $t.ns~ Switch Page Mount the Transmitters Mount Wireless Remote/Transmitter Sensor manufacturer’s instructionsMount the backplate USE Jumpers To Close Loops For Handheld USE Mount Keypad Transmitter Attach the front housing Mount Universal Transmitter Page Auxiliary APPLlCATlONS Panic APPLlCATiONS Comes on when you move Reduce the sensitivity of the Pirt by usingSeveral minutes to stabilize Walk test the Pirt to verify its coverage Exit the Installer Test Mode Choose the Wireless Siren /Controller On = Silent OFF = Sound Switch 9 should Always be onSources of possible RF interference Potential blocks to RF waves Verify that the AC Power Light is on Transformer Plug in the transformerScrew provided #6-32 Until 1 Beep is heard Perform the System Test System Test Hardwired System Test 24-Hour Zone Transmitters RF Scanner