Manuals / Barco / Computer Equipment / Projector

Barco R9002120 manual Projector Set-up, Service Mode, Identification, Data

Models: R9002120

1 57

Download 57 pages 45.14 Kb

Page 40

Projector Set-up

Service Mode

Projector Set-up

Highlight 'Projector Set-Up'by pushing the control disk up or down and press ENTER to display the projector set-up menu.

Within the projector set-up menu, the fol- lowing items can be consultated or set to the desired setting :

-Identification

-Total run time

-Change password

-Change language

-Change projector address

-Change baudrate

-Power up mode

-BARCO logo

SERVICE MODE
PROJECTOR SET-UP
MEMORY MANAGEMENT
COMMON SETTINGS
I2C DIAGNOSTICS
PROJECTOR SET-UP
IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUDRATE
POWER UP MODE : operating
BARCO LOGO
Select with	or
then <ENTER>
<EXIT> to return.

Identification

Highlight 'Identification' with the control disk and press ENTER.

ENTER will start the selected item.

EXIT returns to the Service mode menu.

The 'Identification' screen gives information concerning :

-Projector address. To change the address of your projector, contact a qualified service technician.

-Software version.

-Configuration.

Possible installations :

*Front-ceiling

*Front-table

*Rear-ceiling

*Rear-table

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE : operating

BARCO LOGO

DATA 708

Proj. address : 001

Soft. Version : 6.00

Config. : Ceiling

Front

Baudrate PC : 9600

Text : ON

Serial No. : 103589552

-Baud rate PC : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, contact a qualified service technician to make the appropriate changes.

-Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and failures will be displayed. ON : displayed

OFF : not displayed

The status can be changed by pressing the 'TEXT' key once on the RCU.

-Serial no. : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

7 - 2		5975977 BARCODATA 708 280597

Image 40

Barco R9002120 manual Projector Set-up, Service Mode, Identification, Data

Contents

R9002120 DATAPage BARCO PROJECTION SYSTEMS OWNERS MANUALR9002120 DATABARCO nv/Projection Systems Noordlaan B-8520 Kuurne Belgium Printed in BelgiumTABLE OF CONTENTS TABLE OF CONTENTSSAFETY INSTRUCTIONS Table of ContentsSTART UP OF THE ADJUSTMENT MODE RANDOM ACCESS ADJUSTMENT MODESERVICE MODE Table of ContentsOPTIONS APPENDIX A ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90Table of Contents MESSAGES, WARNINGS AND FAILURESTable of Contents 5975977 BARCODATA 708SAFETY INSTRUCTIONS Safety InstructionsOn safety TO PREVENT FIRE OR ELECTRICAL SHOCKOn installation On cleaningOn servicing On repackingLOCATION AND FUNCTION OF CONTROLS Location and Function of ControlsRear Panel Terminology Front Panel TerminologyControl panel terminology a. The local keypad b. RCU control panel terminologyGaining access Location and Function of ControlsLocation and Function of Controls control disk up = up arrow in the menus control disk down = down arrow in the menusLocation and Function of Controls 5975977 BARCODATA 708Power mains cord connection Switching on/offSignal input connection to the projector 3 CONNECTIONSConnecting a Composite Video source Source NoProjector input Press digit buttonConnecting a S-Video or Video source to port ConnectionsIf a line doubler is built in Input selectionConnecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncConnections RGBS or RGsB input selectionConnecting a Component source Connecting a Component source with Tri-level syncConnections RGB3S or RG3sB input selectionPeripheral equipment Connecting a RCVDS 05 switcher to the projector Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector a remote control4 CONTROLLING Battery installation in the RCUControlling How to use the RCU How to display a projector address?Projector address a. Software set up of the projector addressHow to program an address into the RCU? Input selectionPress button ControllingPicture controls The Pause keyControlling Contrast ControlAdjustment mode START UP OF THE ADJUSTMENT MODESafety Instructions Safety Instructions Warning during the start up of the installation modeRISK OF ELECTRICAL SHOCK NO USER ADJUSTABLE PARTS INSIDE PASSWORDRANDOM ACCESS ADJUSTMENT MODE Random Access Adjustment ModeStarting up the random access adjustment mode Overview random Access Adjustment modeSelecting Setup Pattern Internal Cross Hatch PatternRandom Access Adjustment Mode INTERNAL # PATTERNRandom access adjustment mode selection menu Picture TuningRandom Access Adjustment Mode Fixed Color BalancePeaking Color SelectRandom Access Adjustment Mode Line Doubler optionGeometry Adjustments Horizontal Phase AdjustmentRandom Access Adjustment Mode GEOMETRYRandom Access Adjustment Mode Raster Shift Adjustmentforbidden area phosphor borderLeft-Right east-west Adjustments Random Access Adjustment ModeCorrects the tilting of the vertical lines in the middle of the image Corrects for curvature of the vertical lines on the right sideTop-Bottom north-south Adjustments Random Access Adjustment ModeSize Adjustment Vertical Linearity AdjustmentRandom Access Adjustment Mode H SIZEBlanking Adjustments Random Access Adjustment ModeTop blanking Left blankingRandom Access Adjustment Mode Convergence AdjustmentCONVERGE ADJUSTMENT Random Access Adjustment Mode 5975977 BARCODATA 708SERVICE MODE Service ModeStarting up the Service mode Overview flowchart Service modeProjector Set-up Service ModeIdentification DATAService Mode Change passwordTotal Run Time Change LanguageService Mode Power up modeChange Projector Address Change baudrateMemory management Service ModeWARNING Continuous use of the BARCO logo damages the RED CRT BARCODeletion of blocks Service ModeCopy a block Deleting block by blockService Mode All settings to midpositionUndo all settings to midpos ALL SETTINGS TO MIDPOSService Mode R & B convergence midUndo R & B convergence mid Green convergence midCommon Settings Service ModeG2 Adjustment CRT run in cycleService Mode Projector warm upCRT Drive Mode PROJECTOR WARM UPService Mode I2C DiagnosticsPERMANENT BOOST MODE IN USE Service Mode 5975977 BARCODATAMESSAGES, WARNINGS AND FAILURES Messages, warnings and failuresINPUT Fh= 15.6 kHz Fv= 050 Hz SOURCE enter password x x x text on invalid frequency input table is deleted FAILURE I2C errorWAIT starting up IRIS FAN FAILED Projector will switch off FAILURE RCVDS com munication error FAILURE IRIS commu nication errorMessages, warnings and failures Hardwired RCU VS05 Switcher9 OPTIONS OptionsMAGIK Interface Orbiting KitLine Doubler Kit Ceiling mount CM50ADJUSTMENT BLOCKS AND SOURCE Adjustment Blocks and Source NumbersAdjustment Blocks memory blocks NUMBERS 90Adjustment Blocks and Source Numbers 5975977 BARCODATA 708INSERT CARD Insert CardINPUT SOURCES PROJECTOR