Insert Card | Barco R9002120 specification

Insert Card

INSERT CARD

RCU

INPUT SOURCES

PROJECTOR

1

2

3

4

5

6

7

INPUT SOURCES5932861710 RCVDS

RCU

INPUT SOURCES

PROJECTOR

1

2

3

4

5

6

7

INPUT SOURCES

RCVDS

1

2

3

5

6

7

8

9

10

5975977 BARCODATA 708 260597		i-1

Image 57

Barco R9002120 manual Insert Card

Contents

R9002120 Page Date Art. No 260597 R5975977 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety Instructions On cleaning On installationOn servicing On repacking Location and Function of Controls Rear Panel TerminologyFront Panel Terminology Adjustexit Gaining accessControl panel terminology a. The local keypad RCU control panel terminology Location and Function of Controls Location and Function of Controls Switching on/off Power mains cord connectionSignal input connection to the projector Connections Connecting a Composite Video source Source No Projector input Press digit buttonVideo input selection Input selection Connecting a S-Video or Video source to port Connecting a RGB Analog source with composite sync Connecting a RGB Analog source with Tri-level syncRgbs or RGsB input selection Connecting a Component source with Tri-level sync Connecting a Component sourceRGB3S or RG3sB input selection YYB-YS orR-YYsB-Y input selection Connecting an IR Remote Receiver to the projector Connecting a VS05 switcher to the projectorRemote control YYB-Y3S or R-YY3sB-Y input selection Controlling Battery installation in the RCU How to use the RCU How to display a projector address?Projector address Input selection Source No Projector input Press button How to program an address into the RCU? Pause key Picture controls Adjustexit Standbyenter Adjustment mode Wrong Password Overview random Access Adjustment mode Starting up the random access adjustment mode Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color Balance Port 2 S-Video/Video Line Doubler optionPeaking Color Select Horizontal Phase Adjustment Geometry AdjustmentsGeometry Geometry Projected raster Raster Shift AdjustmentCrt faceplate border Raster Shift Left-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT E-W TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S Size Adjustment Vertical Linearity AdjustmentLinearity Blanking Blanking Adjustments Convergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service mode Projector Set-up IdentificationData Change password Total Run TimeChange Language Change Projector Address Power up modeChange baudrate Baudrate Memory management BARCOlogoBarco Logo Memory Management Copy a block Deletion of blocksDeleting block by block Undo all settings to midpos All settings to midpositionALL Settings to Midpos Undo ALL Settings to Midpos Undo R & B convergence mid Convergence midGreen convergence mid Undo green convergence mid G2 Adjustment Common SettingsCommon Settings G2 Adjustment Projector warm up CRT Drive ModeProjector Warm UP Projector Warm UP Permanent Boost Mode USE I2C Diagnostics Service Mode I2C error Addr FH3 Enter Password Text on Text offFh= 15.6 kHz Fv= 050 Hz Invalid Code entry End of ad- just range Iris commu Nication Error Rcvds com Munication ErrorProjector Will Switch off Starting Options Line Doubler Kit Magik Interface Orbiting KitCeiling mount CM50 Adapter and communication cables Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Barcodata 708 Insert Card