Options

	Table of Contents

MESSAGES, WARNINGS AND FAILURES	8-1
OPTIONS	9-1
IR Receiver 800	9-1
Hardwired RCU	9-1
Projector Control software	9-1
RCVDS 05 Source Selector	9-1
VS05 Switcher	9-1
IRIS/2 Auto-Convergence System	9-1
MAGIK Interface	9-2
Adapter and communication cables	9-2
Orbiting Kit	9-2
Line Doubler Kit	9-2
Ceiling mount CM50	9-2
Soft edge matching kit	9-2
Contrast modulation kit	9-2
APPENDIX A : ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90 - 99	A-1
Adjustment Blocks (memory blocks)	A-1
Source numbers 90 - 99	A-1

5975977 BARCODATA 708 260597		i-3

Page 7

Image 7

Contents

R9002120 Page Date Art. No 260597 R5975977 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Start UP of the Adjustment Mode Options Table of Contents On safety Safety Instructions On repacking On installationOn cleaning On servicing Rear Panel Terminology Location and Function of ControlsFront Panel Terminology RCU control panel terminology Gaining accessAdjustexit Control panel terminology a. The local keypad Location and Function of Controls Location and Function of Controls Connections Power mains cord connectionSwitching on/off Signal input connection to the projector Source No Projector input Press digit button Connecting a Composite Video sourceVideo input selection Input selection Connecting a S-Video or Video source to port Connecting a RGB Analog source with Tri-level sync Connecting a RGB Analog source with composite syncRgbs or RGsB input selection YYB-YS orR-YYsB-Y input selection Connecting a Component sourceConnecting a Component source with Tri-level sync RGB3S or RG3sB input selection YYB-Y3S or R-YY3sB-Y input selection Connecting a VS05 switcher to the projectorConnecting an IR Remote Receiver to the projector Remote control Controlling Battery installation in the RCU How to display a projector address? How to use the RCUProjector address Input selection Source No Projector input Press button How to program an address into the RCU? Pause key Picture controls Adjustexit Standbyenter Adjustment mode Wrong Password Overview random Access Adjustment mode Starting up the random access adjustment mode Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Sync Fast/Slow Adjustment Color Select Line Doubler optionPort 2 S-Video/Video Peaking Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Raster Shift AdjustmentProjected raster Crt faceplate border LEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT E-W TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Vertical Linearity Adjustment Size AdjustmentLinearity Blanking Blanking Adjustments Convergence Adjustment Random Access Adjustment Mode Overview flowchart Service mode Starting up the Service mode Identification Projector Set-upData Total Run Time Change passwordChange Language Baudrate Power up modeChange Projector Address Change baudrate Memory Management BARCOlogoMemory management Barco Logo Deletion of blocks Copy a blockDeleting block by block Undo ALL Settings to Midpos All settings to midpositionUndo all settings to midpos ALL Settings to Midpos Undo green convergence mid Convergence midUndo R & B convergence mid Green convergence mid G2 Adjustment Common SettingsG2 Adjustment Common Settings Projector Warm UP CRT Drive ModeProjector warm up Projector Warm UP Permanent Boost Mode USE I2C Diagnostics Service Mode Invalid Code entry End of ad- just range Enter Password Text on Text offI2C error Addr FH3 Fh= 15.6 kHz Fv= 050 Hz Starting Rcvds com Munication ErrorIris commu Nication Error Projector Will Switch off Options Adapter and communication cables Magik Interface Orbiting KitLine Doubler Kit Ceiling mount CM50 Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Barcodata 708 Insert Card

Barco R9002120 manual Options

Models: R9002120

APPENDIX A : ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90 - 99