Bosch Appliances manual 14.0Faceplates, 14.1D9412GV2 Faceplate

D9412GV2/D7412GV2 Operation and Installation Guide 14.0 Faceplates

14.0Faceplates

14.1D9412GV2 Faceplate

Figure 32: D9412GV2 Faceplate

F01U003643B

1

2

LEDs Off When Normal		D9412GV2
YEL	Charging Status
		Digital Alarm Communicator Transmitter	SDI Connector
	Low Battery - 12.1 VDC
RED		Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)
		For System Wiring Diagram, Issue A	Reset Pin
10.2 VDC - Battery Load Shed		Refer to D9412GV2/D7412GV2 Approved Applications Compliance Guide (P/N: F01U003639___)	Disable all except Battery
			Charging and Programming
		For Compatible Smoke Detectors

11

3

4

5

POWER SUPPLY REQUIREMENTS

CLASS 2 TRANSFORMER

The Power Supply provides a maximum of 1.4 Amps for the Control Panel and all

16.5 VAC 40 VA 60 Hz

Accessory Devices. For System Loading, refer to D9412GV2/D7412GV2

Model D1640

Operation and Installation Guide (P/N: F01U003641___).

Internally Fused - Do not short

All external connections except Terminal 5

(battery positive) are inherently power

Requires Unswitched Outlet

Do not share with other equipment

limited. Requirements for battery standby time might reduce allowable output.

+ AUX POWER

CAUTION: See D9412GV2/D7412GV2 Operation and Installation Guide

(P/N: F01U003641) for Power Requirements relating to Terminals 6 and 7 .

BATTERY NEGATIVE ONLY

WARNING!

Battery: Replace every 3 to

CAUTION: Avoid damage to Panel.

Multi-Battery installation requires

Do not connect 24 V to terminals.

Model D122/D122L Dual Battery

5 years with one or two Model

Maximum charging current 1.4 A

Harness. Improper installation can

D126 12V 7Ah or D1218

BATTERY POSITIVE ONLY

be a fire hazard.

12V 18Ah Lead Acid Batteries.

RELAY A

PROGRAMMABLE

This equipment should be installed in accordance with the NFPA 70 (National Electrical Code)

and NFPA 72 (National Fire Alarm Code) for Local, Central Station, Remote Station, Proprietary and

ALARM OUTPUTS

Household Fire Warning Systems and under the limits of the Local Authority Having Jurisdiction

Terminals

(National Fire Protection Association, Battermarch Park, Quincy, MA 02269). Printed information

RELAY B

6

and 7

describing proper installation, operation, testing, maintenance, evacuation planning and repair

SWITCHED AUX

service is to be provided with this equipment.

RELAY C

Terminal

D9412GV2 Control/Communicator is UL Listed For Central Station, Local, Remote Station and

8

Household Fire Alarm, and Central Station, Local, Police Station Connect, Household Burglar Alarm

and Encrypted Line Security when communicating via a network.

System is intended to be checked by a Qualified Technician at least every 3 years.

COMMON

The types of initiating circuits the panel has been approved for are A, M, W, SS.

VOLTAGE RANGES

EARTH GROUND

Open

3.7 - 5.0 VDC

Normal

2.0 - 3.0 VDC

Short

0.0 - 1.3 VDC

GROUND FAULT DETECT

Point 1 Point 2

Point 3 Point 4

Point 5 Point 6

Point 7 Point 8

Enabled

Disabled

PHONE

ON when

RED

communicating

LED

OFF when idle

PHONE LINE SEIZED

TIP

TELCO CORD RING

11

12 13

14 15 16

17 18 19

20 21 22

MODEL D161

PERIPHERAL DEVICE CONNECTIONS

RED	POWER +
YELLOW	DATA BUS A
GREEN	DATA BUS B
BLACK	COMMON
N.F.P.A.	ZONEX OUT 1
Style 3.5
Signaling
Line
Circuits	ZONEX IN 1
	ZONEX OUT 2	26
	ZONEX IN 2	25

ZONEX POWER +		24
ZONEX COMMON		23
Point 8	D5200/D5360
S3 Option	PROG CONN
Closed = 1KΩ EOL
Normal Operation
Open =AB-12 UL
Bell Box 220 KΩ
GRN

10

PHONE LINE

SEIZED

TIP	RING
	TELCO

6 7 8 9

1 -	Charging status LED (yellow)	7- Point 8 ground fault detect enable/disable
2 -	Low battery LED (red)	8- Operation monitor LED (green)
3 -	Color-coded battery leads	9-	Accessory connector
4 -	Ground fault detect enable	10-	Programming connector
5-	Phone LED (red)	11-	Reset pin
6 -	Telephone cord connector

62 Bosch Security Systems, Inc. 5/05 F01U003641B