Bosch Appliances D9412GV2 manual D7412GV2 uses Points 9 to 75 on Zonex 1 only

D9412GV2/D7412GV2 Operation and Installation Guide 9.0 Off-Board Points

Table 15: D8128D OctoPOPIT Switch Settings for D9412GV2 and D7412GV2

ZONEX 1	D8128D Address Switches					ZONEX 2
Points 9 to						Points 129
127	1	2	3	4	5	to 247
9 to 16	ON	ON	ON	ON	*	129 to 136
17 to 24	ON	ON	ON	OFF	*	137 to 144
25 to 32	ON	ON	OFF	ON	*	145 to 152
33 to 40	ON	ON	OFF	OFF	*	153 to 160
41 to 48	ON	OFF	ON	ON	*	161 to 168
49 to 56	ON	OFF	ON	OFF	*	169 to 176
57 to 64	ON	OFF	OFF	ON	*	177 to 184
65 to 72	ON	OFF	OFF	OFF	*	185 to 192
73 to 80	OFF	ON	ON	ON	*	193 to 200
81 to 88	OFF	ON	ON	OFF	*	201 to 208
89 to 96	OFF	ON	OFF	ON	*	209 to 216
97 to 104	OFF	ON	OFF	OFF	*	217 to 224
105 to 112	OFF	OFF	ON	ON	*	225 to 232
113 to 120	OFF	OFF	ON	OFF	*	233 to 240
121 to 127	OFF	OFF	OFF	ON	*	241 to 247

*Line Termination Switch

For the D8128D OctoPOPITs assigned to Points 121 to 127, 241, and 247, set Point Input Switch 8 to the OPEN position.

D9412GV2 uses Points 9 to 127 on Zonex 1 and Points 129 to 247 on Zonex 2.

D7412GV2 uses Points 9 to 75 on Zonex 1 only.

Table 16: Switch 5 Settings for Line Termination

Is a D8125
POPEX Module				Switch 5 Setting(s) on
connected?		Zonex No.		D8128D OctoPOPIT(s)
	No		NA	Set Switch 5 of only
				one D8128D to ON
	Yes	1		Set Switch 5 of all
				D8128Ds to OFF
	No		NA	Set Switch 5 of only
				one D8128D to ON
	Yes	2		Set Switch 5 of all
				D8128Ds to OFF

Point DIP Switches

Each point connected to the D8128D is enabled by closing the respective DIP switch, or disabled by opening the DIP switch. For example, to disable a device connected to the P3 Terminal (Point 3), move DIP switch number 3 to the OPEN position.

Use the point DIP switches to disable conflicting points, such as when a D9210B Access Control Module must be assigned to a point that falls within the range of the D8128D OctoPOPIT. In this example, a D9210B is assigned to Point 20. On the same system, a D8128D OctoPOPIT is assigned to Points 17 through

24.Moving the DIP switch for Point 4 to the OFF position would effectively disable Point 20, allowing normal operation of the D9210B and the OctoPOPIT.

Terminate each OctoPOPIT sensor loop with a 1 kΩ EOL resistor. Attach a resistor even if you do not enable the loop.

9.4.5Mounting OctoPOPITs

The D8128D OctoPOPIT Module can be installed in the enclosure with the control panel using standard four-conductor 0.8 mm (22 AWG) wire, or in a separate enclosure (Model D8103, D8103A, or D8109) up to 61 m (200 ft.) from the control panel using shielded (recommended) standard four-conductor

0.8mm (22 AWG) wire. If using the D125B or D129, refer to the Specifications section of the D8128D Installation Guide (P/N: 41323) for cabling requirements.

For UL Listed systems, mount the D8128D in a tamper-proof enclosure. To install OctoPOPITs in the control panel’s enclosure, complete the following procedure. Use the D137 Mounting Bracket to install OctoPOPITs in enclosures with no module-mounting locations available.

1.Align the OctoPOPIT module using any of the four mounting locations in the enclosure. Refer to Figure 2 on page 15.

2.Use the screws provided with the module to secure it in the enclosure.

9.4.6	Wiring OctoPOPITs
	Warning: Disconnect all power to the
	control panel before beginning any work
	with the internal components. Serious injury
	could result from electrical shock.

1.Power down the control panel:

a.Disconnect the positive (red) battery lead at the battery.

b.Unplug the transformer.

42 Bosch Security Systems, Inc. 5/05 F01U003641B