Brady 200M, 260M 101

Index

I

Input and Output Signals (Standards Used)

EIA RS-232 and CCITT V.24, 5-2 Inspection, 2-1

Interface Cables

Crossover (Null Modem), 5-4 Straight Through, 5-4

Interface Converter (When Required), 1- 2

Interfaces Parallel, 1-12 RS-232, 1-12

L

Label Available Sensor, 3-3

M

Media Fanfold, 2-10 Loading, 2-7 Roll, 2-7

Media (Types to Use) Card Stock, 1-4 Continuous Roll, 1-4 Fanfold, 1-4

Media Sensor Adjustment Lower, 7-6

Upper, 7-5

Media Transport Mechanism, 1-3 Memory options, 9-2

MODE Key, 3-4

Model Designation Label, 1-1

N

Null Modem, 5-4

Index - 2

O

Operating Modes

Peel-Off, 3-2

Rewind, 3-3

Tear-Off, 3-2

Optional Printer Fonts, D-1

Options

240 VAC Factory Setup, 9-2

P

Parallel Cabling Requirements, 5-5 Parallel Interface, 5-5

Parity (Setting), 4-2 PAUSE Key, 3-2 PAUSE Key Self Test, 3-8 Power (AC)

100/120 Operation, 2-3

220/240 Operation, 2-3

Voltage Selection, 2-2 Premature Head Wear

Perforated Media, 1-4 Print Quality, 1-3

Reflectivity and Contrast, 1-3 Printer Connections

RS-232C Internal Connections, 5-4 Printer Power Up, 2-11

Printer Self Tests CANCEL Key, 3-7 Communications Diagnostics, 3-10 FEED Key, 3-9

Introduction to, 3-6

PAUSE and FEED Keys, 3-10 PAUSE Key, 3-8

Printer Specifications (Complete List- ing), 1-6

Printhead Life

Media Abrasion, 1-3 Printhead Pressure Adjustment, 7-1 Printhead Wear (Guarding Against Pre- mature), 1-3

Contents

Page BradyprinterTM THT Model 200M and 260M Thermal Transfer Printer USER'S GUIDE Proprietary Statement Product Improvements FCC Compliance Statement Canadian DOC Compliance Statement Liability Disclaimer Bradyprinter™ THT Models 200M and 260M WARRANTY INFORMATION 1. Printer Warranty 2. Supplies Warranty 3. Warranty Exclusions and Conditions Table of Contents Introduction Installation Operation Configuration and Calibration Interconnections Preventive Maintenance Troubleshooting Options Appendix A - 240 VAC Power Cord Appendix B - ASCII Code Chart Appendix C - Adjusting Bar Code Darkness Introduction Page Additional System Requirements Media and Ribbon Requirements run tests for your applications Warnings and Precautions CAUTION: CAUTION: Refer to the Interconnections Section Page Printer Specifications Printing Considerations Print Speeds Programmable constant printing speeds of 2″ (51 mm) 3″ (76 mm), 4″ (104 mm), 5“ (127 mm), and 6″ (152 mm) per second Media Ribbon Zebra Programming Language II (ZPL II®) Bar Codes Options Section Page Page Page Installation remove any ribbon and paper roll Power Connection Make sure the fuse you use is correct for the voltage source Appendix A Site Requirements Ribbon Loading Do not 2.Place the Ribbon Roll on the Ribbon Supply Spindle 3.Open the printhead by moving the handle to the OPEN posi- tion Important one: 6.Remove the Hook from the Ribbon Take-UpSpindle Page Media Loading Page Page Page Removing Used Ribbon Initial Printer Power Up Page Operation Page Page Page CANCEL Notes: Page Page Page Whenever the printer is reset to factory defaults, a Media Calibration procedure must be performedimmediately Label Format Qty Speed Page Configuration and Calibration Interconnections Page Configuration Mode IMPORTANT: Page Page Interconnections RS-232Serial Data Port Hardware Control Signal Descriptions RS-232Cabling Requirements To minimize electrical noise pickup in the cable: 1.Keep data cables as short as possible 2.Do not bundle the data cables tightly with power cords Page Data Signal Voltage Level Signal Descriptions Preventive Maintenance Page Page Page Toggle Positioning Printhead Pressure Adjustment Black-MarkMedia Sensor Position Adjustment Transmissive Media Sensor Position Adjustment Page Page 260M only: Page Media and Ribbon Sensor Sensitivity Adjustment Page Troubleshooting Page Page Page ^CC, ^CT, and ^CD Page Options Examples of these Optional Fonts can be found in Appendix D 220-240VAC Factory Setup Memory Options 6-Dot/mmPrinthead (200M Only) Page Page Appendix B - ASCII Code Chart Page Appendix C - Adjusting Bar Code Darkness Too Dark Slightly Dark Slightly Light Too Light In-Spec” Page Page Appendix D - Optional Printer Fonts Page Page Page Appendix E - Support Services Before you call Be prepared W.H. BRADY CO Customer Service Form Complete this form before requesting technical assistance Model # (Be specific: include ALL letters and numbers)