Brady 200M, 260M 96

M-Series User ’s Guide Appendix F - Permasleeve Printing

Printer Calibration

Once the media and ribbon are loaded and the media sensor is in place, the printer must be calibrated.

For the M-Series printer, this is accomplished by pressing the MODE Key until the CALIBRATE light is on and then pressing the FEED Key.

Note: Every time a different type or size of media is run (labels or Permasleeve), this Calibration procedure must be repeated.

Verifying Calibration

After the calibration process is completed, make sure the process was successful by pressing the FEED Key repeatedly, verifying that one sleeve is ejected per press of the FEED Key.

Once the calibration process is completed, the media can be rewound by opening the printhead, manually rewinding the material, and closing the printhead. The printer is now in the PAUSE Mode. Press PAUSE to take the printer out of PAUSE Mode. Five inches of material will then feed out. See leader instructions to eliminate this five inches of waste.

Leader Instructions

Whenever the Printhead is opened, the printer goes off-line and the PAUSE light is lit. To put the printer back on-line, press the PAUSE Key. When it is pressed, five inches of media is ejected.

This five inches of waste is avoided on the first print job of every new roll because there is a leader of empty carrier provided. When starting a print job in the middle of the roll, this empty carrier from the front of the roll can be cut off and reattached to the leading edge of the media. This should be reattached using cellophane (transparent) tape. This provides the user with a method of printing without wasting any sleeves.

F-3

Contents

Page BradyprinterTM THT Model 200M and 260M Thermal Transfer Printer USER'S GUIDE Proprietary Statement Product Improvements FCC Compliance Statement Canadian DOC Compliance Statement Liability Disclaimer Bradyprinter™ THT Models 200M and 260M WARRANTY INFORMATION 1. Printer Warranty 2. Supplies Warranty 3. Warranty Exclusions and Conditions Table of Contents Introduction Installation Operation Configuration and Calibration Interconnections Preventive Maintenance Troubleshooting Options Appendix A - 240 VAC Power Cord Appendix B - ASCII Code Chart Appendix C - Adjusting Bar Code Darkness Introduction Page Additional System Requirements Media and Ribbon Requirements run tests for your applications Warnings and Precautions CAUTION: CAUTION: Refer to the Interconnections Section Page Printer Specifications Printing Considerations Print Speeds Programmable constant printing speeds of 2″ (51 mm) 3″ (76 mm), 4″ (104 mm), 5“ (127 mm), and 6″ (152 mm) per second Media Ribbon Zebra Programming Language II (ZPL II®) Bar Codes Options Section Page Page Page Installation remove any ribbon and paper roll Power Connection Make sure the fuse you use is correct for the voltage source Appendix A Site Requirements Ribbon Loading Do not 2.Place the Ribbon Roll on the Ribbon Supply Spindle 3.Open the printhead by moving the handle to the OPEN posi- tion Important one: 6.Remove the Hook from the Ribbon Take-UpSpindle Page Media Loading Page Page Page Removing Used Ribbon Initial Printer Power Up Page Operation Page Page Page CANCEL Notes: Page Page Page Whenever the printer is reset to factory defaults, a Media Calibration procedure must be performedimmediately Label Format Qty Speed Page Configuration and Calibration Interconnections Page Configuration Mode IMPORTANT: Page Page Interconnections RS-232Serial Data Port Hardware Control Signal Descriptions RS-232Cabling Requirements To minimize electrical noise pickup in the cable: 1.Keep data cables as short as possible 2.Do not bundle the data cables tightly with power cords Page Data Signal Voltage Level Signal Descriptions Preventive Maintenance Page Page Page Toggle Positioning Printhead Pressure Adjustment Black-MarkMedia Sensor Position Adjustment Transmissive Media Sensor Position Adjustment Page Page 260M only: Page Media and Ribbon Sensor Sensitivity Adjustment Page Troubleshooting Page Page Page ^CC, ^CT, and ^CD Page Options Examples of these Optional Fonts can be found in Appendix D 220-240VAC Factory Setup Memory Options 6-Dot/mmPrinthead (200M Only) Page Page Appendix B - ASCII Code Chart Page Appendix C - Adjusting Bar Code Darkness Too Dark Slightly Dark Slightly Light Too Light In-Spec” Page Page Appendix D - Optional Printer Fonts Page Page Page Appendix E - Support Services Before you call Be prepared W.H. BRADY CO Customer Service Form Complete this form before requesting technical assistance Model # (Be specific: include ALL letters and numbers)