For network modules, For WICs and VICs | Cisco Systems 2600 specs

Chapter 3 Installing the Router

Installing Modules, Interface Cards, and Power Supplies

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to support the weight of the unit. Statement 1032

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Note See the “Tools and Equipment for Installation and Maintenance” section on page 2-6for a list of tools and equipment that might be required for your installation.

Installing Modules, Interface Cards, and Power Supplies

Cisco routers are normally shipped with network modules, WAN interface cards (WICs), voice interface cards (VICs), advanced integration modules (AIMs), and power supplies already installed. If you need to remove or install any of these items, refer to the applicable documents online.

For network modules:

•Quick Start Guide: Network Modules for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

•Cisco Network Modules Installation Guide

For WICs and VICs:

•Quick Start Guide: Interface Cards for Cisco 1600, 1700, 2600, 3600, and 3700 Series

•Cisco Interface Cards Installation Guide

For AIMs:

•AIM Installation Quick Start Guide: Cisco 2600, 3600, and 3700 Series

•Installing Advanced Integration Modules in Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

Cisco 2600 Series Routers Hardware Installation Guide

3-2	OL-2171-06

Image 48

Cisco Systems 2600 manual Installing Modules, Interface Cards, and Power Supplies, For network modules, For WICs and VICs

Contents

Cisco 2600 Series Routers Hardware Installation Guide Corporate Headquarters Cisco 2600 Series Routers Hardware Installation Guide N T E N T S Iii Serial DTE or DCE Devices Initial Configuration Using the Setup Command Facility Procedure for the tftpdnld Command Configuration Register Objectives Vii Audience OrganizationConventions Chapter Title Description Safety Warnings Bewaar Deze Instructies Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança Guarde Estas Instruções GEM Disse Anvisninger Xii Xiii Related Documentation Xiv Cisco Product Document Title Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware Xvi Obtaining Documentation Documentation FeedbackCisco.com Ordering Documentation Submitting a Service Request Obtaining Technical AssistanceCisco Technical Support Website Xviii Definitions of Service Request Severity Obtaining Additional Publications and InformationXix Preface Obtaining Additional Publications and Information Hardware Features Overview of Cisco 2600 Series Routers Advanced Cisco Power Reading the Front-Panel LEDs RPS ActivityPWR SYS/RPS Reading the Rear-Panel LEDs ACT Cisco 2613-Rear-Panel LEDs Link ACTFDX Modules, Interface Cards, and Memory CF1 Interface Numbering WAN and LAN Interface Numbering 11 Interface Numbering in Chassis with 1-RU Height System Specifications Description SpecificationVoice Interface Numbering Regulatory Compliance Safety Recommendations Safety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations Power Source Input Power Tolerance LimitsGeneral Site Requirements Site Environment Installation Checklist Site ConfigurationEquipment Racks Creating a Site Log Task Verified by Date Tools and Equipment for Installation and Maintenance Inspecting the Router Console and Auxiliary Port Considerations Console Port Connections Preparing to Connect to a Network Auxiliary Port Connections Ethernet Connections Token Ring Connections Configuring Serial Connections Serial ConnectionsSerial DTE or DCE Devices Signaling Standards Supported Distance LimitationsDevice Type Gender Typical Devices Isdn BRI Connections Asynchronous/Synchronous Serial Module Baud RatesEIA/TIA-232 Distance EIA-530 Distance Rate bps Feet Meters 56-K/Switched-56-kbps DSU/CSU Connections Low-Capacitance Cable OL-2171-06 Installing the Router Installing Modules, Interface Cards, and Power Supplies For network modulesFor WICs and VICs For AIMs Setting Up the Chassis Setting the Chassis on a DesktopFor internal power supplies For external power supplies Mounting the Chassis in a Rack Right To the other side of the chassis. Brackets for 19-inch rack Brackets for 19-inch rack To the other side of the chassis Attaching the Brackets to a Router of 2-RU Height Use two screws on each side For 19-inch rack Right bracket Installing the Router in a Rack V0 EN Mounting the Chassis on the Wall Attaching Rubber Feet to the RouterAttaching Wall-Mount Brackets to the Router Mounting the Router on the Wall 16 Attaching the Wall-Mount Brackets Installing the Chassis Ground Connection 17 Mounting the Chassis on the Wall Ring terminal Power Connections Connecting Routers to AC Power Connecting Routers to a DC-Input Power Supply DC Wiring RequirementsRouter DC Input DC Input Wire Size1 15A, 120VAC 10A, 240VAC. Statement Wiring Procedure for DC Input Connecting WAN, LAN, and Voice Cables Connecting Routers to the Cisco Redundant Power SystemPorts and Cabling Port or Connection Port Type, Color Connected To Cable LAN, WAN, and Voice Connection Procedures Connecting to a Console Terminal or Modem Connecting to the Console Port Connecting to the Auxiliary Port 23 Connecting to a Console Terminal 24 Connecting a Modem to the Auxiliary Port Identifying a Rollover Cable Powering Up the Router Checklist for Power UpFront Panel Indicators Routers with 1-RU Chassis Height Power-Up Procedure Routers with 2-RU Chassis Height Configuring the Router Initial Configuration Using SDM Initial Configuration Using the Setup Command Facility Enter a hostname for the router this example uses Initial Configuration Using the CLI Manual Configuration Configuration is displayed To proceed with manual configuration using the CLI, enter no OL-2171-06 Troubleshooting Isolating Problems Troubleshooting the Power and Cooling Systems Environmental Reporting Features Troubleshooting Modules, Cables, and Connections Recovering a Lost Password System MessagesCisco Technical Assistance Center Using the ROM Monitor Entering ROM Monitor Mode ROM Monitor Commands Enter ROM Monitor Mode by Using the reload Command ROM Monitor Command Syntax Conventions Command abc ROM Monitor Command Descriptions Router Management CommandsBoot Commands in the ROM Monitor Informational Commands in the ROM Monitor Debugging Commands Other Useful ROM Monitor Commands Configuration Register Commands Modifying the Configuration Register in Menu Mode Recovering Cisco IOS Software Images Modifying the Configuration Register by Hexidecimal Entry Copying an Image from the Console Using the xmodem Command Description and Options of the xmodem CommandProcedure for the xmodem Command Console Requirements Restrictions on the tftpdnld Command Procedure for the tftpdnld Command Specify the required variables, for example DEFAULTGATEWAY=172.16.19.1 Configuration Register Settings Bit Number Hexadecimal MeaningNvram Changing Configuration Register Settings Configuring the Boot Field Boot Field Meaning Bit Address net host Enabling Booting from Flash Memory Baud Bit OL-2171-06 Numerics IN-1 Dram IN-2 Isdn BRI LANLink LED IN-3 Sdram IN-4 IN-5 IN-6