Mounting the Router on the Wall | Cisco Systems 2600 specs

Chapter 3 Installing the Router

Setting Up the Chassis

Figure 3-16 Attaching the Wall-Mount Brackets

Mounting the Router on the Wall

After fastening the brackets to the chassis, mount the chassis on the wall:

•Orient the front and rear of the chassis vertically.

•Position the end nearest the power cable at the top.

•Align the screws (not included) with a wall stud, or use wall anchors.

•Figure 3-17shows a typical wall-mounted installation.

Cisco 2600 Series Routers Hardware Installation Guide

3-12	OL-2171-06

Image 58

Cisco Systems 2600 manual Mounting the Router on the Wall, Attaching the Wall-Mount Brackets

Contents

Cisco 2600 Series Routers Hardware Installation Guide Corporate Headquarters Cisco 2600 Series Routers Hardware Installation Guide N T E N T S Iii Serial DTE or DCE Devices Initial Configuration Using the Setup Command Facility Procedure for the tftpdnld Command Configuration Register Objectives Vii Conventions AudienceOrganization Chapter Title Description Safety Warnings Bewaar Deze Instructies Warnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança Guarde Estas Instruções GEM Disse Anvisninger Xii Xiii Related Documentation Xiv Cisco Product Document Title Replacement, Repair, or Refund Policy for Hardware Cisco 90-Day Limited Hardware Warranty TermsDuration of Hardware Warranty Xvi Cisco.com Obtaining DocumentationDocumentation Feedback Ordering Documentation Cisco Technical Support Website Submitting a Service RequestObtaining Technical Assistance Xviii Obtaining Additional Publications and Information Definitions of Service Request SeverityXix Preface Obtaining Additional Publications and Information Hardware Features Overview of Cisco 2600 Series Routers Advanced Cisco Power Reading the Front-Panel LEDs PWR RPSActivity SYS/RPS Reading the Rear-Panel LEDs ACT Cisco 2613-Rear-Panel LEDs ACT LinkFDX Modules, Interface Cards, and Memory CF1 Interface Numbering WAN and LAN Interface Numbering 11 Interface Numbering in Chassis with 1-RU Height Description Specification System SpecificationsVoice Interface Numbering Regulatory Compliance Safety Recommendations Safety with Electricity Preventing Electrostatic Discharge Damage General Site Requirements Power Supply ConsiderationsPower Source Input Power Tolerance Limits Site Environment Site Configuration Installation ChecklistEquipment Racks Creating a Site Log Task Verified by Date Tools and Equipment for Installation and Maintenance Inspecting the Router Console and Auxiliary Port Considerations Console Port Connections Preparing to Connect to a Network Auxiliary Port Connections Ethernet Connections Token Ring Connections Serial Connections Configuring Serial ConnectionsSerial DTE or DCE Devices Distance Limitations Signaling Standards SupportedDevice Type Gender Typical Devices EIA/TIA-232 Isdn BRI ConnectionsAsynchronous/Synchronous Serial Module Baud Rates Distance EIA-530 Distance Rate bps Feet Meters 56-K/Switched-56-kbps DSU/CSU Connections Low-Capacitance Cable OL-2171-06 Installing the Router For WICs and VICs Installing Modules, Interface Cards, and Power SuppliesFor network modules For AIMs For internal power supplies Setting Up the ChassisSetting the Chassis on a Desktop For external power supplies Mounting the Chassis in a Rack Right To the other side of the chassis. Brackets for 19-inch rack Brackets for 19-inch rack To the other side of the chassis Attaching the Brackets to a Router of 2-RU Height Use two screws on each side For 19-inch rack Right bracket Installing the Router in a Rack V0 EN Attaching Rubber Feet to the Router Mounting the Chassis on the WallAttaching Wall-Mount Brackets to the Router Mounting the Router on the Wall 16 Attaching the Wall-Mount Brackets Installing the Chassis Ground Connection 17 Mounting the Chassis on the Wall Ring terminal Power Connections Connecting Routers to AC Power Router DC Input DC Input Wire Size1 Connecting Routers to a DC-Input Power SupplyDC Wiring Requirements 15A, 120VAC 10A, 240VAC. Statement Wiring Procedure for DC Input Ports and Cabling Connecting WAN, LAN, and Voice CablesConnecting Routers to the Cisco Redundant Power System Port or Connection Port Type, Color Connected To Cable LAN, WAN, and Voice Connection Procedures Connecting to a Console Terminal or Modem Connecting to the Console Port Connecting to the Auxiliary Port 23 Connecting to a Console Terminal 24 Connecting a Modem to the Auxiliary Port Identifying a Rollover Cable Front Panel Indicators Powering Up the RouterChecklist for Power Up Routers with 1-RU Chassis Height Power-Up Procedure Routers with 2-RU Chassis Height Configuring the Router Initial Configuration Using SDM Initial Configuration Using the Setup Command Facility Enter a hostname for the router this example uses Initial Configuration Using the CLI Manual Configuration Configuration is displayed To proceed with manual configuration using the CLI, enter no OL-2171-06 Troubleshooting Isolating Problems Troubleshooting the Power and Cooling Systems Environmental Reporting Features Troubleshooting Modules, Cables, and Connections System Messages Recovering a Lost PasswordCisco Technical Assistance Center Using the ROM Monitor Entering ROM Monitor Mode ROM Monitor Commands Enter ROM Monitor Mode by Using the reload Command ROM Monitor Command Syntax Conventions Command abc Router Management Commands ROM Monitor Command DescriptionsBoot Commands in the ROM Monitor Informational Commands in the ROM Monitor Debugging Commands Other Useful ROM Monitor Commands Configuration Register Commands Modifying the Configuration Register in Menu Mode Recovering Cisco IOS Software Images Modifying the Configuration Register by Hexidecimal Entry Procedure for the xmodem Command Copying an Image from the Console Using the xmodem CommandDescription and Options of the xmodem Command Console Requirements Restrictions on the tftpdnld Command Procedure for the tftpdnld Command Specify the required variables, for example DEFAULTGATEWAY=172.16.19.1 Bit Number Hexadecimal Meaning Configuration Register SettingsNvram Changing Configuration Register Settings Configuring the Boot Field Boot Field Meaning Bit Address net host Enabling Booting from Flash Memory Baud Bit OL-2171-06 Numerics IN-1 Dram IN-2 Link LED Isdn BRILAN IN-3 Sdram IN-4 IN-5 IN-6