Using the Device Manager | Cisco Systems 3120 guide

Chapter 1 Product Overview

Management Options

Using the Device Manager

The simplest way to manage the switch module is by using the device manager that is in the switch module memory. This is a web interface that offers quick configuration and monitoring. You can access the device manager from anywhere in your network through a web browser.

Follow these steps:

1.Launch a web browser on your PC or workstation.

2.Enter the switch module IP address in the web browser, and press Enter. The device manager page appears. (See Figure 1-2.)

Figure 1-2 Device Manager Page

3.Use the device manager to perform basic switch module configuration and monitoring. Refer to the device manager online help for more information.

4.For more advanced configuration, download and run the Cisco Network Assistant, which is described in the next section.

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

	OL-12246-01	1-9

Image 19

Cisco Systems 3120 manual Using the Device Manager

Contents

Americas Headquarters MarchPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Purpose AudienceOrganization Related Publications Conventions Preface OL-12246-01 Product Overview Switch Module Features Overview Port Description UID 1 LED Switch Module Console Port Other Features LRM 10/100/1000 PortsGigabit Ethernet Module Slots Cisco TwinGig Converter Module Color System Status LEDsSystem LED Stack LED RJ-45 Uplink Port LEDs Stack Master LEDStack Member LED UID and Health LEDs Gigabit Ethernet Module Slot Port LEDs X2 Module Installed Only the CBS3120X Switch Management Options Power ConnectorsStackWise Plus Ports Device Manager Using the Device Manager Network Configurations Using the Command-Line Interface Preparing for Installation Switch Installation Safety Warnings Installation Guidelines Verifying Package Contents Rear View of the Blade Enclosure HP c-Class BladeSystem Enclosure Architecture Statement Installing the Switch Module in the Blade Enclosure Open the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Express Setup Advanced Settings Table Using Express Setup Enter switch 1 priority Setting the Installed Switch Module As the Stack Master Refreshing the PC IP Address Planning and Creating a Switch Stack Stack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module Removing a Module 12 Installing X2 Transceiver Modules Installing an SFP Module Installing SFP Modules Removing an SFP Module 14 Converter Module with SFP Modules Installed 15 Connecting to an Ethernet Port Connecting to the 10/100/1000 Ports Planning 10/100/1000 Ethernet Port Connections Device Crossover Cable Where to Go Next Switch Installation Where to Go Next Verify the Switch Module Post Results Diagnosing Problems Ethernet and Fiber Cables Look at the Switch Module LEDsConfirm the Switch Module Connections Bad or Damaged Cable Spanning Tree Loops SFP Module Port IssuesPort and Interface Settings Ping the End Device Cabling Distance Verify the Switch Module PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network-Interface Cards Replacing a Failed Stack Member Clearing the Switch Module IP Address and Configuration 250310 Locating the Switch Module Serial Number OL-12246-01 Environmental Ranges Physical Dimensions OL-12246-01 Connector Specifications Connector and Cable Specifications Connecting to 1000BASE-T Devices Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices Cisco TwinGig Converter Module Ports Gigabit Ethernet Module Interfaces Microns MHz/km Distance Cable and Adapter SpecificationsGigabit Ethernet X2 Transceiver Module Cable Specifications Console Port Transmit X2 Product Transmit Power Receive Power NumberDBm Wavelength nm GLC-SX-MM SFP Module Cable SpecificationsTwo Twisted-Pair Cable Pinouts 1000BASE-SX TP3 Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Device Switch Console RJ-45-to-DB-9 Port DTEIdentifying a Crossover Cable Console Port Adapter Pinouts Switch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Connecting to the Console Port Accessing the CLI Through the Console Port OL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear CLI Numerics IN-2 Post UID IN-4 LED IN-5 IN-6