Verifying Package Contents | Cisco Systems 3120 guide

Chapter 2 Switch Installation

Preparing for Installation

Verifying Package Contents

Carefully remove the contents from the shipping container, and look at each item for damage. If any item is missing or damaged, contact your Cisco representative or reseller for support. Return all packing material to the shipping container, and save it.

These items ship with your switch module. The Cisco TwinGig Converter Modules with installed protective dust covers are shipped already installed on your switch module.

•Console cable

•1-meter Stackwise Plus cable

•Documentation CD that contains:

–Cisco Catalyst Blade Switch 3000 Series for HP Getting Started Guide

–Regulatory Compliance and Safety Information for the Cisco Catalyst Blade Switch 3000 Series for HP

–Cisco and HP Warranty Information

Note If the switch modules are ordered with the blade enclosure, the switch modules are already installed, and no unpacking is required. The unpacking procedure applies only if a switch module is ordered separately.

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

2-4	OL-12246-01

Image 24

Cisco Systems 3120 manual Verifying Package Contents

Contents

March Americas HeadquartersPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Audience PurposeOrganization Conventions Related Publications Preface OL-12246-01 Switch Module Features Overview Product Overview UID 1 LED Port Description Other Features Switch Module Console Port 10/100/1000 Ports Gigabit Ethernet Module SlotsCisco TwinGig Converter Module LRM LEDs System LEDStack LED Color System Status Stack Master LED Stack Member LEDUID and Health LEDs RJ-45 Uplink Port LEDs X2 Module Installed Only the CBS3120X Switch Gigabit Ethernet Module Slot Port LEDs Power Connectors Management OptionsStackWise Plus Ports Using the Device Manager Device Manager Using the Command-Line Interface Network Configurations Switch Installation Preparing for Installation Safety Warnings Installation Guidelines Verifying Package Contents HP c-Class BladeSystem Enclosure Architecture Rear View of the Blade Enclosure Installing the Switch Module in the Blade Enclosure Statement Open the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Using Express Setup Express Setup Advanced Settings Table Setting the Installed Switch Module As the Stack Master Enter switch 1 priority Planning and Creating a Switch Stack Refreshing the PC IP Address Stack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module 12 Installing X2 Transceiver Modules Removing a Module Installing SFP Modules Installing an SFP Module 14 Converter Module with SFP Modules Installed Removing an SFP Module Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet Port Planning 10/100/1000 Ethernet Port Connections Where to Go Next Device Crossover Cable Switch Installation Where to Go Next Diagnosing Problems Verify the Switch Module Post Results Look at the Switch Module LEDs Confirm the Switch Module ConnectionsBad or Damaged Cable Ethernet and Fiber Cables SFP Module Port Issues Port and Interface SettingsPing the End Device Spanning Tree Loops Verify the Switch Module Performance Speed, Duplex, and AutonegotiationAutonegotiation and Network-Interface Cards Cabling Distance Clearing the Switch Module IP Address and Configuration Replacing a Failed Stack Member Locating the Switch Module Serial Number 250310 OL-12246-01 Physical Dimensions Environmental Ranges OL-12246-01 Connector and Cable Specifications Connector Specifications Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices Connecting to 1000BASE-T Devices Gigabit Ethernet Module Interfaces Cisco TwinGig Converter Module Ports Cable and Adapter Specifications Gigabit Ethernet X2 Transceiver Module Cable SpecificationsConsole Port Microns MHz/km Distance X2 Product Transmit Power Receive Power Number TransmitDBm Wavelength nm SFP Module Cable Specifications Two Twisted-Pair Cable Pinouts1000BASE-SX GLC-SX-MM Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports TP3 Switch Console RJ-45-to-DB-9 Port DTE Identifying a Crossover CableConsole Port Adapter Pinouts Device Switch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Accessing the CLI Through the Console Port Connecting to the Console Port OL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear Numerics CLI IN-2 UID Post LED IN-4 IN-5 IN-6