These choices appear | Cisco Systems 3120 manual

Appendix C Configuring the Switch with the CLI-Based Setup Program

Accessing the CLI Through the Console Port

!

interface Vlan1 no shutdown

ip address 10.0.0.1 255.255.255.0

!

interface GigabitEthernet0/1

!

interface GigabitEthernet0/2

. . . (output truncated)

interface GigabitEthernet0/16

!

end

Step 10 These choices appear:

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

If you want to save the configuration and use it the next time the switch reboots, save it in NVRAM by selecting option 2.

Enter your selection [2]:2

Make your selection, and press Return.

Step 11 Disconnect the blade server serial port or the switch module console port from the PC. See the “Management Options” section on page 1-8for information about managing the switch module.

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

	C-6	OL-12246-01

Image 70

Cisco Systems 3120 manual These choices appear

Contents

March Americas HeadquartersPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Purpose AudienceOrganization Conventions Related Publications Preface OL-12246-01 Switch Module Features Overview Product Overview UID 1 LED Port Description Other Features Switch Module Console Port Cisco TwinGig Converter Module 10/100/1000 PortsGigabit Ethernet Module Slots LRM Stack LED LEDsSystem LED Color System Status UID and Health LEDs Stack Master LEDStack Member LED RJ-45 Uplink Port LEDs X2 Module Installed Only the CBS3120X Switch Gigabit Ethernet Module Slot Port LEDs Management Options Power ConnectorsStackWise Plus Ports Using the Device Manager Device Manager Using the Command-Line Interface Network Configurations Switch Installation Preparing for Installation Safety Warnings Installation Guidelines Verifying Package Contents HP c-Class BladeSystem Enclosure Architecture Rear View of the Blade Enclosure Installing the Switch Module in the Blade Enclosure Statement Open the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Using Express Setup Express Setup Advanced Settings Table Setting the Installed Switch Module As the Stack Master Enter switch 1 priority Planning and Creating a Switch Stack Refreshing the PC IP Address Stack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module 12 Installing X2 Transceiver Modules Removing a Module Installing SFP Modules Installing an SFP Module 14 Converter Module with SFP Modules Installed Removing an SFP Module Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet Port Planning 10/100/1000 Ethernet Port Connections Where to Go Next Device Crossover Cable Switch Installation Where to Go Next Diagnosing Problems Verify the Switch Module Post Results Bad or Damaged Cable Look at the Switch Module LEDsConfirm the Switch Module Connections Ethernet and Fiber Cables Ping the End Device SFP Module Port IssuesPort and Interface Settings Spanning Tree Loops Autonegotiation and Network-Interface Cards Verify the Switch Module PerformanceSpeed, Duplex, and Autonegotiation Cabling Distance Clearing the Switch Module IP Address and Configuration Replacing a Failed Stack Member Locating the Switch Module Serial Number 250310 OL-12246-01 Physical Dimensions Environmental Ranges OL-12246-01 Connector and Cable Specifications Connector Specifications Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices Connecting to 1000BASE-T Devices Gigabit Ethernet Module Interfaces Cisco TwinGig Converter Module Ports Console Port Cable and Adapter SpecificationsGigabit Ethernet X2 Transceiver Module Cable Specifications Microns MHz/km Distance Transmit X2 Product Transmit Power Receive Power NumberDBm Wavelength nm 1000BASE-SX SFP Module Cable SpecificationsTwo Twisted-Pair Cable Pinouts GLC-SX-MM Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports TP3 Console Port Adapter Pinouts Switch Console RJ-45-to-DB-9 Port DTEIdentifying a Crossover Cable Device Switch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Accessing the CLI Through the Console Port Connecting to the Console Port OL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear Numerics CLI IN-2 UID Post LED IN-4 IN-5 IN-6