Removing a Module | Cisco Systems 3120 guide

Chapter 2 Switch Installation

Installing Devices in the 10-Gigabit Ethernet Slots

Figure 2-12 Installing X2 Transceiver Modules

SYST S-MODE S-MSTR S-MMBR

UID

MODE

CONSOLE

19-20

23x

22 24x

26x

	STK A
WS-	STK B
WS-
CBS312	0G-S

250299

Caution Do not install the converter module with SFP modules or cables installed. Always remove any cables and modules before installing the converter module in the slot.

Figure 2-13 Installing Converter Modules

SYST S-MODE S-MSTR S-MMBR

UID

MODE CONSOLE

19-20

23x

SFP 21-22 24x

26x

	STK A
WS-	STK B
WS-
CBS312	0G-S

250300

Removing a Module

To remove an X2 transceiver module or a converter module, follow these steps:

Step 1 Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.

Step 2 For X2 transceiver modules, disconnect the cables from the module. For fiber-optic modules, install the optical bore dust plugs.

Step 3 For converter modules, disconnect the cables from the SFP module. Remove the SFP modules from the converter module.

Caution Do not remove the converter module with SFP modules or cables installed. Always remove any cables and modules before removing the converter module from the slot.

Step 4 Carefully pull on the X2 module sleeve, or pinch the tabs on the converter module to disengage it from the slot. Grasp the edges of the module, and carefully slide it out of the slot.

		Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

	OL-12246-01			2-19
	OL-12246-01			2-19

Image 39

Cisco Systems 3120 manual Removing a Module, Installing X2 Transceiver Modules

Contents

Americas Headquarters MarchPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Audience PurposeOrganization Related Publications Conventions Preface OL-12246-01 Product Overview Switch Module Features Overview Port Description UID 1 LED Switch Module Console Port Other Features LRM 10/100/1000 PortsGigabit Ethernet Module Slots Cisco TwinGig Converter Module Color System Status LEDsSystem LED Stack LED RJ-45 Uplink Port LEDs Stack Master LEDStack Member LED UID and Health LEDs Gigabit Ethernet Module Slot Port LEDs X2 Module Installed Only the CBS3120X Switch Power Connectors Management OptionsStackWise Plus Ports Device Manager Using the Device Manager Network Configurations Using the Command-Line Interface Preparing for Installation Switch Installation Safety Warnings Installation Guidelines Verifying Package Contents Rear View of the Blade Enclosure HP c-Class BladeSystem Enclosure Architecture Statement Installing the Switch Module in the Blade Enclosure Open the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Express Setup Advanced Settings Table Using Express Setup Enter switch 1 priority Setting the Installed Switch Module As the Stack Master Refreshing the PC IP Address Planning and Creating a Switch Stack Stack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module Removing a Module 12 Installing X2 Transceiver Modules Installing an SFP Module Installing SFP Modules Removing an SFP Module 14 Converter Module with SFP Modules Installed 15 Connecting to an Ethernet Port Connecting to the 10/100/1000 Ports Planning 10/100/1000 Ethernet Port Connections Device Crossover Cable Where to Go Next Switch Installation Where to Go Next Verify the Switch Module Post Results Diagnosing Problems Ethernet and Fiber Cables Look at the Switch Module LEDsConfirm the Switch Module Connections Bad or Damaged Cable Spanning Tree Loops SFP Module Port IssuesPort and Interface Settings Ping the End Device Cabling Distance Verify the Switch Module PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network-Interface Cards Replacing a Failed Stack Member Clearing the Switch Module IP Address and Configuration 250310 Locating the Switch Module Serial Number OL-12246-01 Environmental Ranges Physical Dimensions OL-12246-01 Connector Specifications Connector and Cable Specifications Connecting to 1000BASE-T Devices Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices Cisco TwinGig Converter Module Ports Gigabit Ethernet Module Interfaces Microns MHz/km Distance Cable and Adapter SpecificationsGigabit Ethernet X2 Transceiver Module Cable Specifications Console Port X2 Product Transmit Power Receive Power Number TransmitDBm Wavelength nm GLC-SX-MM SFP Module Cable SpecificationsTwo Twisted-Pair Cable Pinouts 1000BASE-SX TP3 Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports Device Switch Console RJ-45-to-DB-9 Port DTEIdentifying a Crossover Cable Console Port Adapter Pinouts Switch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Connecting to the Console Port Accessing the CLI Through the Console Port OL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear CLI Numerics IN-2 Post UID IN-4 LED IN-5 IN-6