Completing the Initial Configuration | Cisco Systems 3120 specs

Appendix C Configuring the Switch with the CLI-Based Setup Program

Accessing the CLI Through the Console Port

Configure the baud rate and character format of the PC or terminal to match these console port default characteristics:

•9600 baud

•8 data bits

•1 stop bit

•No parity

•None (flow control)

Step 3 Wait for the switch module to complete the POST. It might take several minutes for the switch module to complete POST.

Step 4 Verify that POST has completed by confirming that the system and status LEDs remain green.

If the switch module fails POST, the system LED turns amber. POST errors are usually fatal. Call Cisco Systems immediately if your switch module fails POST.

Step 5 Wait for the switch to complete initialization. When you see the prompt, Press Return to Get Started!, press Return or Enter.

Step 6 Make sure that the system and status LEDs are green. This means that the switch module is operating properly.

Step 7 See the “Completing the Initial Configuration” section on page C-4for instructions on setting up and initially configuring the switch module.

Completing the Initial Configuration

Follow these steps to complete the setup program and to create an initial configuration for the switch module.

Note For information about automatically configuring the switch module, see the “Assigning the Switch IP Address and Default Gateway” chapter in the switch module configuration guide.

Step 1 After you have pressed Enter or Return after the prompt to start the initial configuration setup program, enter yes at these prompts:

Would you like to terminate autoinstall? [yes]: yes

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: yes

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: yes

Configuring global parameters:

Cisco Catalyst Blade Switch 3120 for HP Hardware Installation Guide

	C-4	OL-12246-01

Image 68

Cisco Systems 3120 manual Completing the Initial Configuration

Contents

March Americas HeadquartersPage N T E N T S Setup Accessing the CLI Through the Console Port OL-12246-01 Organization AudiencePurpose Conventions Related Publications Preface OL-12246-01 Switch Module Features Overview Product Overview UID 1 LED Port Description Other Features Switch Module Console Port 10/100/1000 Ports Gigabit Ethernet Module SlotsCisco TwinGig Converter Module LRM LEDs System LEDStack LED Color System Status Stack Master LED Stack Member LEDUID and Health LEDs RJ-45 Uplink Port LEDs X2 Module Installed Only the CBS3120X Switch Gigabit Ethernet Module Slot Port LEDs StackWise Plus Ports Power ConnectorsManagement Options Using the Device Manager Device Manager Using the Command-Line Interface Network Configurations Switch Installation Preparing for Installation Safety Warnings Installation Guidelines Verifying Package Contents HP c-Class BladeSystem Enclosure Architecture Rear View of the Blade Enclosure Installing the Switch Module in the Blade Enclosure Statement Open the Release Latch Switch Module IP Addresses Switch Installation Onboard Administrator Interconnect Bay Summary Window Using Express Setup Express Setup Advanced Settings Table Setting the Installed Switch Module As the Stack Master Enter switch 1 priority Planning and Creating a Switch Stack Refreshing the PC IP Address Stack Cabling Configurations 250304 Connecting to the StackWise Plus Ports Installing Devices in the 10-Gigabit Ethernet Slots Installing a Transceiver or Converter Module 12 Installing X2 Transceiver Modules Removing a Module Installing SFP Modules Installing an SFP Module 14 Converter Module with SFP Modules Installed Removing an SFP Module Connecting to the 10/100/1000 Ports 15 Connecting to an Ethernet Port Planning 10/100/1000 Ethernet Port Connections Where to Go Next Device Crossover Cable Switch Installation Where to Go Next Diagnosing Problems Verify the Switch Module Post Results Look at the Switch Module LEDs Confirm the Switch Module ConnectionsBad or Damaged Cable Ethernet and Fiber Cables SFP Module Port Issues Port and Interface SettingsPing the End Device Spanning Tree Loops Verify the Switch Module Performance Speed, Duplex, and AutonegotiationAutonegotiation and Network-Interface Cards Cabling Distance Clearing the Switch Module IP Address and Configuration Replacing a Failed Stack Member Locating the Switch Module Serial Number 250310 OL-12246-01 Physical Dimensions Environmental Ranges OL-12246-01 Connector and Cable Specifications Connector Specifications Connecting to 10BASE-T- and 100BASE-TX-Compatible Devices Connecting to 1000BASE-T Devices Gigabit Ethernet Module Interfaces Cisco TwinGig Converter Module Ports Cable and Adapter Specifications Gigabit Ethernet X2 Transceiver Module Cable SpecificationsConsole Port Microns MHz/km Distance DBm Wavelength nm X2 Product Transmit Power Receive Power NumberTransmit SFP Module Cable Specifications Two Twisted-Pair Cable Pinouts1000BASE-SX GLC-SX-MM Four Twisted-Pair Cable Pinouts for 1000BASE-T Ports TP3 Switch Console RJ-45-to-DB-9 Port DTE Identifying a Crossover CableConsole Port Adapter Pinouts Device Switch Console RJ-45-to-DB-25 Port DTE OL-12246-01 Accessing the CLI Through the Console Port Connecting to the Console Port OL-12246-01 Figure C-1 Connecting through the Switch Module Console Port Completing the Initial Configuration To configure Snmp now, enter yes These choices appear Numerics CLI IN-2 UID Post LED IN-4 IN-5 IN-6