Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems IGX 8400 Series manual H9888

Models: IGX 8400 Series

1 52

Download 52 pages 51.44 Kb

Page 21

Image 21

Installing Voice Cards

Figure 3-9 Pass-Through and Standard (External) UVM E1 Cabling

Pass-throughPassed-

through

Passing (transparent)

A. One pass-through line

UVM 1

UVM 2

External

B. External line	UVM	H9888

The back slot line numbers correspond to the slot number in which the BC-UVI-2E1EC card resides. Record the back slot number and port number of each line. These numbers are necessary for conﬁguring the system after you complete hardware installation.

Card Installation and Node Startup 3-21

Page 21

Image 21

Cisco Systems IGX 8400 Series manual H9888

Contents

Preparing the Cards Card Installation and Node StartupC H A P T E R A Cisco IGX node can support a conﬁguration of up to 32 trunks H8385 Preparing the Cards Figure 3-2 IGX 8410 Cards, Front ViewPreparing the Cards 3-4 Cisco IGX 8400 Series Installation and ConfigurationFigure 3-3 IGX 8410 Cards, Back View ARI recommended location General purpose card slotsPreparing the Cards Card Installation and Node StartupFigure 3-4 IGX 8420 Card Shelf, Front View General purpose card slotsPreparing the Cards 3-6 Cisco IGX 8400 Series Installation and ConfigurationFigure 3-5 IGX 8430 Back View H8347Inserting the Cards Making Signal Connections Connecting Trunks Setting Up a UXM-EBringing Up a UXM-E Trunk 3-10 Cisco IGX 8400 Series Installation and Configuration Setting Up a UXM-EFigure 3-7 Cable Management Cable manager Cable manager Frame bonding connectionInverse Multiplexing over ATM on Trunks dspcdscnfclksrc Adding Links to an IMA Feeder Group Adding an IMA Feeder Trunkuptrk slot.startport-endport uptrk slot.group-membersRemoving Links from an IMA Feeder Group UXM-E Inverse Multiplexing ATM IMA Linesupln slot.group-member cnftrk slot.primary linkConnecting an NTM T1 or Y1 Trunk Connecting an NTM E1 or Subrate Trunk3-14 Cisco IGX 8400 Series Installation and Configuration Setting Up a UXM-E Bringing Up a UXM-E in UNI or NNI Port ModeConnecting a CVM to a T1 or J1 Line Installing Voice CardsTDM Transport on the CVM Connecting a CVM to an E1 Line or a Subrate TrunkConnecting a UVM to T1 Lines Card Installation and Node Startup Installing Voice CardsFigure 3-8 Pass-Through and Standard External UVM T1 Cabling H98843-20 Cisco IGX 8400 Series Installation and Configuration Connecting a UVM to E1 LinesH9888 3-22 Cisco IGX 8400 Series Installation and Configuration Connecting a UVM to J1 LinesThe back slot line numbers correspond to the slot number in which the BC-UVI-2J1EC card resides. Record the back slot number and port number of each line. These numbers are necessary for conﬁguring the system after you complete hardware installation Making Serial Data Connections Making Serial Data ConnectionsFigure 3-11 SDI and LDI Faceplates Conﬁguring the Port Modes of the HDM Back Cards HDM and LDM Redundancy Conﬁguring the Mode of an LDI Port3-26 Cisco IGX 8400 Series Installation and Configuration Card Installation and Node Startup Figure 3-13 Connecting a DTE or DCE Adapter Cable to an LDIconnector Making Serial Data ConnectionsSetting Up Frame Relay on a UFM Maximum Connections Per Port with Signalling ProtocolsMaking Frame Relay Connections Y-Cable Redundancy on the UFMsStandard cable with 2 ports cab2 Y-cable Standard cable Y-cable UFI-4HSSI, UFI-12V.35, or UFI-12X.21UFI-12X.21 or UFI-12V.35 H10047Setting Up Frame Relay Ports and Connections UFM Connecting UFM CablingCommands for T1/E1 Frame Relay Setting Up Frame Relay on an FRMDeleting a Frame Relay Port Reference3-32 Cisco IGX 8400 Series Installation and Configuration Port Mode Selection for V.35 andFrame Relay Card Redundancy 3-34 Cisco IGX 8400 Series Installation and Configuration Setting Up Frame Relay Ports and Connections FRMMaking Alarm Relay Output Connections Commands for T1/E1 Frame RelayDeleting a Frame Relay Port Step 3 Observe that the ACTIVE LED on the ARM card is on Making External Clock Connections Connecting a Single Network Management StationAttaching Peripherals Cisco StrataView Plus Operations GuideAttach the control terminal to the SCM. See Figure Attaching Peripherals LAN Connection for the Network Management StationFigure 3-17 LAN Connection to SCM H8359Conﬁguring the LAN Port A cnﬂan screen looks like this 9.3 Feb. 27 2000 1427 PST 3-42 Cisco IGX 8400 Series Installation and ConfigurationBackbone 192.187.207.1 Router 192.187.207.11 192.187.207.21 Connecting a Network Management Station to Multiple Networks192.187.207.200 Router AUI 192.187.210.1 SV+ 192.187.210.30 SCM Note IP numbers are representative onlyConnecting the Printer H8361 Connecting a ModemInitial Startup of the IGX Connecting the Power Supply MonitorNPM Startup Diagnostic Test Inspecting Status Lights Card Self TestIGX Conﬁguration Summary Checking the Power Supplies AC Systems3-50 Cisco IGX 8400 Series Installation and Configuration Interworking Connections in a Tiered Network Conﬁguring an IGX Switch to Be an Interface ShelfConverting a Routing Node to an Interface Shelf Adding Connections in a Tiered Network through the CLIaddcon slot.port.DLCI localnodename slot.vpi1.vci1 addcon slot.port.vpi1.vci1 remotenodename slot.port.vpi2.vci2