Manuals / Cisco Systems / Computer Equipment / Switch

Cisco Systems IGX 8400 Series manual Connecting a Network Management Station to Multiple Networks

Models: IGX 8400 Series

1 52

Download 52 pages 51.44 Kb

Page 43

Backbone

Attaching Peripherals

Figure 3-18 SV+ LAN Connection via Router to an IGX Node

Backbone

192.187.207.1

Router

192.187.207.11

192.187.207.21

192.187.207.200

Router

AUI

192.187.210.1

SV+

192.187.210.30

SCM

Note: IP numbers are representative only.

H8374

Figure 3-19 SV+ LAN Connection to an IGX Node (No Gateway)

192.187.207.200

AUI

SV+

Note: IP numbers are representative only.

192.187.207.30

SCM

H8375

Step 7 Switch on the control terminal (or Cisco WAN Manager workstation). Adjust the terminal’s conﬁguration, if necessary, to match the default settings of the control terminal port in the IGX node. See the Cisco WAN Manager Operations publication for settings and operating instructions for the workstations.

Connecting a Network Management Station to Multiple Networks

When a network management station has more than one serial port, ports can connect to different networks. When the number of workstation serial ports is less than the number of networks to be managed, a terminal server is necessary to obtain a communications link to the separate networks. This subject is covered in the Cisco WAN Manager Installation publication.

Card Installation and Node Startup 3-43

Image 43

Cisco Systems IGX 8400 Series manual Connecting a Network Management Station to Multiple Networks, 192.187.207.30 SCM

Contents

Card Installation and Node Startup Preparing the CardsC H A P T E R A Cisco IGX node can support a conﬁguration of up to 32 trunks H8385 Preparing the Cards Figure 3-2 IGX 8410 Cards, Front ViewARI recommended location General purpose card slots 3-4 Cisco IGX 8400 Series Installation and ConfigurationPreparing the Cards Figure 3-3 IGX 8410 Cards, Back ViewGeneral purpose card slots Card Installation and Node StartupPreparing the Cards Figure 3-4 IGX 8420 Card Shelf, Front ViewH8347 3-6 Cisco IGX 8400 Series Installation and ConfigurationPreparing the Cards Figure 3-5 IGX 8430 Back ViewInserting the Cards Making Signal Connections Setting Up a UXM-E Connecting TrunksBringing Up a UXM-E Trunk Cable manager Cable manager Frame bonding connection Setting Up a UXM-E3-10 Cisco IGX 8400 Series Installation and Configuration Figure 3-7 Cable Managementdspcds Inverse Multiplexing over ATM on Trunkscnfclksrc uptrk slot.group-members Adding an IMA Feeder TrunkAdding Links to an IMA Feeder Group uptrk slot.startport-endportcnftrk slot.primary link UXM-E Inverse Multiplexing ATM IMA LinesRemoving Links from an IMA Feeder Group upln slot.group-memberConnecting an NTM E1 or Subrate Trunk Connecting an NTM T1 or Y1 Trunk3-14 Cisco IGX 8400 Series Installation and Configuration Setting Up a UXM-E Bringing Up a UXM-E in UNI or NNI Port ModeConnecting a CVM to a T1 or J1 Line Installing Voice CardsTDM Transport on the CVM Connecting a CVM to an E1 Line or a Subrate TrunkConnecting a UVM to T1 Lines H9884 Installing Voice CardsCard Installation and Node Startup Figure 3-8 Pass-Through and Standard External UVM T1 Cabling3-20 Cisco IGX 8400 Series Installation and Configuration Connecting a UVM to E1 LinesH9888 3-22 Cisco IGX 8400 Series Installation and Configuration Connecting a UVM to J1 LinesThe back slot line numbers correspond to the slot number in which the BC-UVI-2J1EC card resides. Record the back slot number and port number of each line. These numbers are necessary for conﬁguring the system after you complete hardware installation Making Serial Data Connections Making Serial Data ConnectionsFigure 3-11 SDI and LDI Faceplates Conﬁguring the Port Modes of the HDM Back Cards Conﬁguring the Mode of an LDI Port HDM and LDM Redundancy3-26 Cisco IGX 8400 Series Installation and Configuration Making Serial Data Connections Figure 3-13 Connecting a DTE or DCE Adapter Cable to an LDICard Installation and Node Startup connectorY-Cable Redundancy on the UFMs Maximum Connections Per Port with Signalling ProtocolsSetting Up Frame Relay on a UFM Making Frame Relay ConnectionsH10047 Standard cable Y-cable UFI-4HSSI, UFI-12V.35, or UFI-12X.21Standard cable with 2 ports cab2 Y-cable UFI-12X.21 or UFI-12V.35Setting Up Frame Relay Ports and Connections UFM Connecting UFM CablingReference Setting Up Frame Relay on an FRMCommands for T1/E1 Frame Relay Deleting a Frame Relay Port3-32 Cisco IGX 8400 Series Installation and Configuration Port Mode Selection for V.35 andFrame Relay Card Redundancy 3-34 Cisco IGX 8400 Series Installation and Configuration Setting Up Frame Relay Ports and Connections FRMCommands for T1/E1 Frame Relay Making Alarm Relay Output ConnectionsDeleting a Frame Relay Port Step 3 Observe that the ACTIVE LED on the ARM card is on Cisco StrataView Plus Operations Guide Connecting a Single Network Management StationMaking External Clock Connections Attaching PeripheralsAttach the control terminal to the SCM. See Figure H8359 LAN Connection for the Network Management StationAttaching Peripherals Figure 3-17 LAN Connection to SCMConﬁguring the LAN Port A cnﬂan screen looks like this 9.3 Feb. 27 2000 1427 PST 3-42 Cisco IGX 8400 Series Installation and ConfigurationNote IP numbers are representative only Connecting a Network Management Station to Multiple NetworksBackbone 192.187.207.1 Router 192.187.207.11 192.187.207.21 192.187.207.200 Router AUI 192.187.210.1 SV+ 192.187.210.30 SCMConnecting the Printer H8361 Connecting a ModemInitial Startup of the IGX Connecting the Power Supply MonitorNPM Startup Diagnostic Test Inspecting Status Lights Card Self TestIGX Conﬁguration Summary Checking the Power Supplies AC Systems3-50 Cisco IGX 8400 Series Installation and Configuration Interworking Connections in a Tiered Network Conﬁguring an IGX Switch to Be an Interface Shelfaddcon slot.port.vpi1.vci1 remotenodename slot.port.vpi2.vci2 Adding Connections in a Tiered Network through the CLIConverting a Routing Node to an Interface Shelf addcon slot.port.DLCI localnodename slot.vpi1.vci1