Parity | Compaq R6000 guide

Configuration 4-19

Parity

Choose the desired parity from the 5 available choices.

Serial Port 1

→Parity

■odd

■even

■none

■mark

■space

An asterisk, “*” appears beside the selected value.

Serial Port 2

This port is configured with the same steps as shown above for Serial Port 1.

Image 74

Compaq R6000 manual Parity

Contents

Compaq R6000 Series UPS Operation and Reference Guide Page Contents Operation Configuration Appendix B Text Conventions Symbols in TextAbout This Guide Symbols on Equipment Viii Compaq R6000 Series UPS Operation and Reference Guide Compaq Technical Support Rack StabilityGetting Help Compaq Website Compaq Authorized Reseller Compaq R6000 UPS Series Models IntroductionCompaq R6000 UPS Series Models UPS Model Part Number Comments Front Panel R6000 front panel Rear Panel Compaq R6000 UPS Features Communication Ports Solid green means normal operation Front Panel LEDsLED Meaning Flashing green means Standby Front Panel Controls and LCD Display Control Name Function Power Management Software Compaq Power Management Software UPS Option Cards Hardware OptionsHardware Options Option Part Number Scalable Option Card MatrixCase Compaq Multi-Server UPS Card Multi-Server UPS Card Compaq Scalable UPS Card Scalable UPS Card Compaq SNMP-EN Adapter SNMP-EN Adapter Power Distribution Units PDUs Extended Runtime Modules ERMs $25,000 Computer Load Protection Guarantee WarrantyRemote Emergency Power Off Repo Port Pre-Failure Battery Warranty Installation Important Safety Instructions About This Device Position Installation ConsiderationsWeight Outline of Installation Procedure Preparing the Rack Check Battery Recharge LabelUnpacking the UPS Assembling the Compaq R6000 UPS Placing UPS in rack Placing chassis in rack Wiring the Compaq R6000 UPS 8Compaq R6000 Series UPS Operation and Reference Guide High Leakage Current Connecting the Compaq R6000 UPS to AC Branch CircuitRisk of Fire Notice Electrical Safety Requirements Procedure Recommendation Input Wiring Removing terminal input block cover Install and connect the battery packs Sliding battery packs into chassis Connect cables 11. Connecting battery packs to the Compaq R6000 UPS Attaching Front Top Bezel 12. Attaching the top front bezel Installing Extended Runtime Modules ERMs Connecting Communications Ports Connecting Communication Ports to Other Devices Load Segments Description Connecting LoadsInstalling and Connecting Communication Options Load Effect on Backup Time Ordering Extra Power CordsConfiguring Load Segments Attaching the Load Segments Completing the Assembly R6000 UPS in the Rack 16. Placing the battery circuit breaker in the on position Pressing the on button Powering up the R6000 UPSTurning on the Main Circuit Breaker Shutting Down the System Installation is Now Complete Charging Batteries Operation Front Panel Controls Front Panel Indicators Front Panel LCD Front Panel LEDs Ref # Description Standby Mode Modes of Operation Battery Mode Audible Alarm Initiating a Self-test Silencing an Audible Alarm Silencing an audible alarm Configuration Changing Configuration Parameters Range Matching the Utility VoltageVoltage Ranges VAC Configuring the Compaq R6000 UPS Using the LCD Display Menu LCD display, showing the three buttons that control it Top Level Main Menu Initial Power-Up DisplayLCD Display Menu Structure Sub-Menu Choices Status UPS Status + Load Segment status Load Power Off UPS Status + Active Alarm CountOn Battery Load Power On Input Volts MetersOverload Output Volts Battery Volts Active AlarmsOutput Power Output Frequency Input Over or Under Frequency Input AC Over VoltageInput AC Under Voltage Output Overload Battery Totally Discharged Inverter FaultBattery Low UPS on Battery Site Wiring Fault Battery DataBattery Test Failed Firmware Version Load Control Display Test System Setup Set Hardware HW Configuration Battery Setup Set Language Set Alarm Horn Set Password Serial Port Communications SetupSet Sync Range ±Hertz Baud Rate Data Bits Stop Bits Parity Set Voltage Set Site FaultSet Sleep Mode Battery Maintenance Precautions When to Replace Batteries Obtaining New Batteries Before Replacing Batteries How to Replace BatteriesRemoving the Battery Packs Place the battery circuit breaker in the OFF position Disconnecting the battery cables Slide out the Compaq R6000 UPS battery packs Installing New Batteries Test/Reset Alarm button Extended Runtime Module ERM Batteries Disposing of Used BatteriesCare and Storage of Batteries Troubleshooting Causes Action Shutdown Imminent Responding to Audible AlarmsAudible Alarm Group Causes Action Shutdown within Seconds Loads in Jeopardy Audible Alarm Causes Action Low, refer to Chapter 6Compaq R6000 UPS Series Operation and Reference Guide Responding to Audible Alarms Audible Alarm Group Battery breaker is in the on Compaq R6000 UPS Trouble Indicators Trouble Indicators LED Alarm Configurations Repairing the UPS Regulatory Compliance Notices Federal Communications Commission Notice Class a Equipment Class B Equipment Canadian Notice Avis Canadien European Union Notice Class A/B Equipment Japanese NoticeTaiwanese Notice Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Table C-1 Physical Characteristics Physical SpecificationsInput Specifications Table C-2 Input Specifications Output Specifications Regulation IV. Additional FeaturesII. Output Voltage Battery Specifications Battery SpecificationsBattery Runtime Table C-4 Environmental Specifications Table C-6 Environmental Specifications Index Battery cable connectors Button controls Index Compaq 6000 Series UPS Operation and Reference Guide See Compaq 6000 Series UPS Operation and Reference Guide Replacement battery kit part Compaq 6000 Series UPS Operation and Reference Guide Options tabulated Compaq 6000 Series UPS Operation and Reference Guide