Attaching Front Top Bezel | Compaq R6000 manual

Installation 2-15

Attaching Front Top Bezel

1.Attach the connectors for the Front Panel to the Electronics Module receptacles ( ).

2. Lift the bezel into place ( ).

Figure 2-12. Attaching the top front bezel

3. Secure the bezel to the chassis using the captive screws on each side.

Figure 2-13. Securing the top front bezel to the chassis

NOTE: Leave lower bezel off until wiring and installation is complete.

Image 40

Compaq R6000 manual Attaching Front Top Bezel, Attaching the top front bezel

Contents

Compaq R6000 Series UPS Operation and Reference Guide Page Contents Operation Configuration Appendix B About This Guide Symbols in TextText Conventions Symbols on Equipment Viii Compaq R6000 Series UPS Operation and Reference Guide Getting Help Rack StabilityCompaq Technical Support Compaq Website Compaq Authorized Reseller Introduction Compaq R6000 UPS Series ModelsCompaq R6000 UPS Series Models UPS Model Part Number Comments Front Panel R6000 front panel Rear Panel Compaq R6000 UPS Features Communication Ports Front Panel LEDs LED MeaningSolid green means normal operation Flashing green means Standby Front Panel Controls and LCD Display Control Name Function Power Management Software Compaq Power Management Software Hardware Options Hardware OptionsUPS Option Cards Option Part Number Case Option Card MatrixScalable Compaq Multi-Server UPS Card Multi-Server UPS Card Compaq Scalable UPS Card Scalable UPS Card Compaq SNMP-EN Adapter SNMP-EN Adapter Power Distribution Units PDUs Extended Runtime Modules ERMs Remote Emergency Power Off Repo Port Warranty$25,000 Computer Load Protection Guarantee Pre-Failure Battery Warranty Installation Important Safety Instructions About This Device Weight Installation ConsiderationsPosition Outline of Installation Procedure Unpacking the UPS Check Battery Recharge LabelPreparing the Rack Assembling the Compaq R6000 UPS Placing UPS in rack Placing chassis in rack Wiring the Compaq R6000 UPS 8Compaq R6000 Series UPS Operation and Reference Guide Risk of Fire Notice Electrical Safety Requirements Connecting the Compaq R6000 UPS to AC Branch CircuitHigh Leakage Current Procedure Recommendation Input Wiring Removing terminal input block cover Install and connect the battery packs Sliding battery packs into chassis Connect cables 11. Connecting battery packs to the Compaq R6000 UPS Attaching Front Top Bezel 12. Attaching the top front bezel Installing Extended Runtime Modules ERMs Connecting Communications Ports Connecting Communication Ports to Other Devices Installing and Connecting Communication Options Connecting LoadsLoad Segments Description Ordering Extra Power Cords Configuring Load SegmentsLoad Effect on Backup Time Attaching the Load Segments Completing the Assembly R6000 UPS in the Rack 16. Placing the battery circuit breaker in the on position Powering up the R6000 UPS Turning on the Main Circuit BreakerPressing the on button Shutting Down the System Installation is Now Complete Charging Batteries Operation Front Panel Controls Front Panel Indicators Front Panel LCD Front Panel LEDs Ref # Description Standby Mode Modes of Operation Battery Mode Audible Alarm Initiating a Self-test Silencing an Audible Alarm Silencing an audible alarm Configuration Changing Configuration Parameters Voltage Ranges VAC Matching the Utility VoltageRange Configuring the Compaq R6000 UPS Using the LCD Display Menu LCD display, showing the three buttons that control it Initial Power-Up Display LCD Display Menu StructureTop Level Main Menu Sub-Menu Choices Status UPS Status + Load Segment status UPS Status + Active Alarm Count On BatteryLoad Power Off Load Power On Meters OverloadInput Volts Output Volts Active Alarms Output PowerBattery Volts Output Frequency Input AC Over Voltage Input AC Under VoltageInput Over or Under Frequency Output Overload Inverter Fault Battery LowBattery Totally Discharged UPS on Battery Battery Test Failed Battery DataSite Wiring Fault Firmware Version Load Control Display Test System Setup Set Hardware HW Configuration Battery Setup Set Language Set Alarm Horn Set Password Communications Setup Set Sync Range ±HertzSerial Port Baud Rate Data Bits Stop Bits Parity Set Sleep Mode Set Site FaultSet Voltage Battery Maintenance Precautions When to Replace Batteries Obtaining New Batteries Removing the Battery Packs How to Replace BatteriesBefore Replacing Batteries Place the battery circuit breaker in the OFF position Disconnecting the battery cables Slide out the Compaq R6000 UPS battery packs Installing New Batteries Test/Reset Alarm button Care and Storage of Batteries Disposing of Used BatteriesExtended Runtime Module ERM Batteries Troubleshooting Audible Alarm Group Responding to Audible AlarmsCauses Action Shutdown Imminent Causes Action Shutdown within Seconds Loads in Jeopardy Audible Alarm Causes Action Low, refer to Chapter 6Compaq R6000 UPS Series Operation and Reference Guide Responding to Audible Alarms Audible Alarm Group Battery breaker is in the on Compaq R6000 UPS Trouble Indicators Trouble Indicators LED Alarm Configurations Repairing the UPS Regulatory Compliance Notices Federal Communications Commission Notice Class a Equipment Class B Equipment Canadian Notice Avis Canadien European Union Notice Taiwanese Notice Japanese NoticeClass A/B Equipment Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Physical Specifications Input SpecificationsTable C-1 Physical Characteristics Table C-2 Input Specifications Output Specifications II. Output Voltage IV. Additional FeaturesRegulation Battery Specifications Battery RuntimeBattery Specifications Table C-4 Environmental Specifications Table C-6 Environmental Specifications Index Battery cable connectors Button controls Index Compaq 6000 Series UPS Operation and Reference Guide See Compaq 6000 Series UPS Operation and Reference Guide Replacement battery kit part Compaq 6000 Series UPS Operation and Reference Guide Options tabulated Compaq 6000 Series UPS Operation and Reference Guide