Compaq R6000 manual

Battery Maintenance 5-5

2.Using a Philips screwdriver, remove the lower front bezel by backing off the captive screws on each side.

Figure 5-2. Removing screws from the lower front bezel

3. Place the battery circuit breaker in the OFF position.

WARNING: To reduce the risk of personal injury, once the bezel is removed, the battery circuit breakers MUST be in the OFF position before continuing with the battery replacement.

Figure 5-3. Placing the battery circuit breaker in the OFF position

Image 80

Compaq R6000 manual Place the battery circuit breaker in the OFF position

Contents

Compaq R6000 Series UPS Operation and Reference Guide Page Contents Operation Configuration Appendix B Text Conventions Symbols in TextAbout This Guide Symbols on Equipment Viii Compaq R6000 Series UPS Operation and Reference Guide Compaq Technical Support Rack StabilityGetting Help Compaq Website Compaq Authorized Reseller Introduction Compaq R6000 UPS Series ModelsCompaq R6000 UPS Series Models UPS Model Part Number Comments Front Panel R6000 front panel Rear Panel Compaq R6000 UPS Features Communication Ports Front Panel LEDs LED MeaningSolid green means normal operation Flashing green means Standby Front Panel Controls and LCD Display Control Name Function Power Management Software Compaq Power Management Software Hardware Options Hardware OptionsUPS Option Cards Option Part Number Scalable Option Card MatrixCase Compaq Multi-Server UPS Card Multi-Server UPS Card Compaq Scalable UPS Card Scalable UPS Card Compaq SNMP-EN Adapter SNMP-EN Adapter Power Distribution Units PDUs Extended Runtime Modules ERMs $25,000 Computer Load Protection Guarantee WarrantyRemote Emergency Power Off Repo Port Pre-Failure Battery Warranty Installation Important Safety Instructions About This Device Position Installation ConsiderationsWeight Outline of Installation Procedure Preparing the Rack Check Battery Recharge LabelUnpacking the UPS Assembling the Compaq R6000 UPS Placing UPS in rack Placing chassis in rack Wiring the Compaq R6000 UPS 8Compaq R6000 Series UPS Operation and Reference Guide High Leakage Current Connecting the Compaq R6000 UPS to AC Branch CircuitRisk of Fire Notice Electrical Safety Requirements Procedure Recommendation Input Wiring Removing terminal input block cover Install and connect the battery packs Sliding battery packs into chassis Connect cables 11. Connecting battery packs to the Compaq R6000 UPS Attaching Front Top Bezel 12. Attaching the top front bezel Installing Extended Runtime Modules ERMs Connecting Communications Ports Connecting Communication Ports to Other Devices Load Segments Description Connecting LoadsInstalling and Connecting Communication Options Ordering Extra Power Cords Configuring Load SegmentsLoad Effect on Backup Time Attaching the Load Segments Completing the Assembly R6000 UPS in the Rack 16. Placing the battery circuit breaker in the on position Powering up the R6000 UPS Turning on the Main Circuit BreakerPressing the on button Shutting Down the System Installation is Now Complete Charging Batteries Operation Front Panel Controls Front Panel Indicators Front Panel LCD Front Panel LEDs Ref # Description Standby Mode Modes of Operation Battery Mode Audible Alarm Initiating a Self-test Silencing an Audible Alarm Silencing an audible alarm Configuration Changing Configuration Parameters Range Matching the Utility VoltageVoltage Ranges VAC Configuring the Compaq R6000 UPS Using the LCD Display Menu LCD display, showing the three buttons that control it Initial Power-Up Display LCD Display Menu StructureTop Level Main Menu Sub-Menu Choices Status UPS Status + Load Segment status UPS Status + Active Alarm Count On BatteryLoad Power Off Load Power On Meters OverloadInput Volts Output Volts Active Alarms Output PowerBattery Volts Output Frequency Input AC Over Voltage Input AC Under VoltageInput Over or Under Frequency Output Overload Inverter Fault Battery LowBattery Totally Discharged UPS on Battery Site Wiring Fault Battery DataBattery Test Failed Firmware Version Load Control Display Test System Setup Set Hardware HW Configuration Battery Setup Set Language Set Alarm Horn Set Password Communications Setup Set Sync Range ±HertzSerial Port Baud Rate Data Bits Stop Bits Parity Set Voltage Set Site FaultSet Sleep Mode Battery Maintenance Precautions When to Replace Batteries Obtaining New Batteries Before Replacing Batteries How to Replace BatteriesRemoving the Battery Packs Place the battery circuit breaker in the OFF position Disconnecting the battery cables Slide out the Compaq R6000 UPS battery packs Installing New Batteries Test/Reset Alarm button Extended Runtime Module ERM Batteries Disposing of Used BatteriesCare and Storage of Batteries Troubleshooting Causes Action Shutdown Imminent Responding to Audible AlarmsAudible Alarm Group Causes Action Shutdown within Seconds Loads in Jeopardy Audible Alarm Causes Action Low, refer to Chapter 6Compaq R6000 UPS Series Operation and Reference Guide Responding to Audible Alarms Audible Alarm Group Battery breaker is in the on Compaq R6000 UPS Trouble Indicators Trouble Indicators LED Alarm Configurations Repairing the UPS Regulatory Compliance Notices Federal Communications Commission Notice Class a Equipment Class B Equipment Canadian Notice Avis Canadien European Union Notice Class A/B Equipment Japanese NoticeTaiwanese Notice Battery Replacement Notice Electrostatic Discharge Grounding Methods Specifications Physical Specifications Input SpecificationsTable C-1 Physical Characteristics Table C-2 Input Specifications Output Specifications Regulation IV. Additional FeaturesII. Output Voltage Battery Specifications Battery RuntimeBattery Specifications Table C-4 Environmental Specifications Table C-6 Environmental Specifications Index Battery cable connectors Button controls Index Compaq 6000 Series UPS Operation and Reference Guide See Compaq 6000 Series UPS Operation and Reference Guide Replacement battery kit part Compaq 6000 Series UPS Operation and Reference Guide Options tabulated Compaq 6000 Series UPS Operation and Reference Guide