Application, DR-8 | Compex Systems AP4530 instruction

Application

iDR-8User Guide

Installed, live and special project sound

Installer configured, operator controlled

Set and forget, remote control

Zoned sound distribution and control

Paging and background music

Source routing and mixing

Signal equalisation and dynamics processing

Automatic microphone mixing

Venue speaker management

System time alignment

		iDR-in
	MODEM
PL Designer software		iDR-out
PL Designer software	RS232
PL Client software	RS232
PL Client software		iDR-out
'Vitual' wall plates	NETWORK
		AUDIO MONITOR
		iDR-8
		DR-8
		AUDIO MIX PROCESSOR
	DR-Link	Sys-Net
		MIDI
iDR-switch

iDR-switch

PL-Anet

Switch closures

Open-collector logic

Relays

Lamps

Infra-red

REMOTE CONTROLLERS

iDR System Manager software

AUDIO EXPANDERS

System configuration

AUDIO EXPANDERS

System configuration

Page 41

Image 41

Compex Systems AP4530 manual Application, DR-8

Contents

IDR-8 Conditions Of Warranty Limited One Year Warranty Important Mains Plug Wiring Instructions Important Safety Instructions Read FirstThis appliance must be earthed IDR-8User Guide Introduction Contents DR-8 Welcome to the iDR-8 IDR-8 main processing unit 2U, 8 mic/line Main FeaturesDaisy chain iDR-8 units Any number may be Stereo audio monitor with front panel Expander status LEDs These display Front Panel OverviewFront panel RS232 port This is used for Monitor in L Monitor OUT L Rear Panel Overview System Processing Overview IDR-8User Guide Page IDR System Manager Software Bundle Getting Started Check the Contents IDR-8 Main Unit Installing the iDR-8 Earthing Turning the iDR-8 On and Off Parameters restored on power-up The iDR-8Starting Offline with iDR System Manager Software Updating the iDR-8 Operating Code Checking the iDR-8 Operating Code Version PPP Setup IDR-8 Setup Menus Checking the Current Settings and Status Accessing the iDR-8 Setup MenusRebooting the iDR-8 Changing the Unit Name DR-8 Getting Started Checking the Hardware RS232 COM Port Communicating with the iDR-8Network Port Communicating Using a TCP/IP Connection Connecting the iDR-8 to a Network Connecting the iDR-8 Direct to the PCHow to get the MAC address Connect the PC to the iDR-8 Plug the PC Ethernet port Setting up a Dial-up Connection Communicating Using a Dial Up ConnectionChanging the iDR-8 PPP settings Go to menu *6 PPP Setting up the PC dial-up connection You need Dial up the iDR-8 using the remote PC Open up Connecting the iDR-8 to a ModemStarting the iDR System Manager Connect the iDR-8 to the modem Archiving and Loading Configurations Setting the Time and Day ClockWorking with the iDR System Manager Start the iDR System Manager from the Start / Programs Input Source window From within the Input XLR Analogue Inputs and Outputs Monitor TRS Input and Output The monitor is Monitor Headphones Output This followsMonitor Inputs and Outputs Daisy chaining iDR-8 monitors The active Using the Monitor as Additional Channels Check the connections The iDR-inAUDIO OUT Adding the iDR-in and iDR-out Audio ExpandersTurning the expander on or off Turn the unit on Checking for expanders You can use the front Expanded multiple iDR-8 system This diagram Slave Linking iDR-8 Units Unit a Connecting to the iDR-8 The iDR-8communicates Adding the iDR-switch ExpanderChecking for iDR-switch expanders You can Using the switch closure inputs The input is Connectors and grounding Pluggable Phoenix Using the logic outputs Each output is opto Selecting the Communications Options Click on MIDI, SysNet and PL-Anet PortsSysNet IDR-8 Memory System IDR-8 unit settings These areConfiguration file settings These are Only store the parameters you need For your Starting with the PatchesDecide your system starting point Assign DR-8 Technical Specification DR-8 Application IDR-switch Front Panel IDR-8 Installer Front PanelHeadphones Description IDR-switch Logic Outputs IDR-switch InputsPower Supply Network Port Software Soft SwitchesClock Naming Signal Generator DelayLevel Control Fader Groups Factory default patch parameters Factory default unit settingsFactory default configuration settings Template for Allen & Heath iDR-8 Front Panel Key Label