Features Status and Indications | Compex Technologies WPE54 specification

	Appendix IV	Panel Views and Descriptions


	Appendix IV	Panel Views and Descriptions

5

1

2

3

4

	Features			Status and Indications

1	LAN	Link/Act	Steady Yellow	The access point is operating at the speed of
	LED			10Mbps.
			Steady Green	The access point is operating at the speed of
				100Mbps.
2	WLAN	Link/Act	Steady Green	More than 1 wireless client is present in the
	LED			wireless network.
			Blinking Green	Activity is detected in the wireless network.
3	Diagnostic LED		Steady Green	The device is in access point or gateway
				mode.
			Blinking Green	The device is booting.
			Off	The device is in Client mode.
4	Power LED		Steady Blue	Power is supplied to the device.
			Off	No power is supplied to the device.
5	Antenna		2dbi antenna

131

Image 132

Compex Technologies WPE54 manual Features Status and Indications, Appendix Panel Views and Descriptions

Contents

Page Trademark Information DisclaimerYour Feedback FCC Notice Declaration of Conformity Technical Support Information Compex, Inc How to Use this Document About This DocumentFirmware Conventions Chapter Hardware Installation Chapter Further Configuration Appendix Troubleshooting 118 Hardware Installation Product Overview Features and BenefitsIntroduction Hardware Installation When to use which mode STP Access Point Mode Access Point Client Mode Gateway Mode Static IP addressDynamic IP address PPP over Ethernet PPPoE Singapore Adsl Ethernet 512KAustralia BPA Cable Wireless Routing Client Mode Wireless Ethernet Adapter Mode Wireless Bridge Link Mode Setup Requirements Hardware Installation Access to Web-based Interface Access to the Web interface with uConfigThrough our Utility uConfig Access to Web-based Interface Access to Web-based Interface Direct access to web-based interface via Internet Explorer Access to Web-based Interface Access to Web-based Interface Access to Web-based Interface Common Configuration Management Port SetupManagement Port Wlan Basic Setup Wlan Security STP Setup Setting up your LAN Parameters Description Common Configuration To view the active Dhcp leases View Active Dhcp LeasesGo to the Advanced Dhcp Server Reserve Specific IP addresses Common Configuration Delete Dhcp Server Reservation Wlan Setup BasicSecurity Advanced To configure the Basic setup of the wireless mode Basic Setup Wireless Mode Common Configuration Common Configuration To configure the Advanced setup of the wireless mode Advanced Setup Wireless ModeWlan Advanced Setup AP/Gateway mode only Common Configuration Scan for Site Survey Scan For Site Survey Ssid Show Link Information Show Link InformationLink Information section Link Information table illustrates the following data Wireless Extended Features Features ModeAccess Control The Wireless Pseudo Vlan Wireless Pseudo Vlan Per Node Wireless Pseudo Vlan Per Node Wireless Pseudo Vlan Per Group Wireless Pseudo Vlan Per Group Common Configuration Delete client from a group Wireless Pseudo Vlan Tag Vlan Tag Vlan Common Configuration Delete client from a Tag Vlan Wireless Setup The Wireless Distributed System WDS Star Configuration WDS Chain Configuration WDS WDS Configuration Setup At the Edit WDS Link page which shows Click on the Back button to return to the WDS Status Common Configuration WMM Parameters WMM Parameters WMM Parameters for advanced users Long Distance Parameters available in all modes Long Distance Parameters ACK Timeout CTS TimeoutOutdoor Distance Selecting Security Mode Security Mode is set toWlan Security How to set up WEP Available in ALL modes Security Mode -WEPWhen using 64-bit encryption When using 128-bit encryption Further Configuration How to set up WPA-PSKSecurity Mode -WPA-PSK, WPA2-PSK, WPA-PSK-AUTO At the Wlan Security Setup Further Configuration Security Mode -802.1x/RADIUS Radius Server, if any How to set up WPA EAP Security Mode WPA-EAP, WPA2-EAP, WPA-EAP-AUTO Further Configuration STP Setup Further Configuration Further Configuration Bandwidth STP Cost Scenario #1 No STP, No Pseudo Vlan Scenario #2 With STP, No Pseudo Vlan Scenario #3 With STP and Pseudo Vlan Enabling STP Setup Forwarding DelayPriority Hello Time Snmp Setup MAC FilteringEnabling Snmp Enabling MAC Filtering Setting up uConfig UConfig Set up Configuring WAN Setup Click on WAN Setup from the Configuration menuChanging WAN Type Changing WAN Type Dynamic IP Configuration At the Dynamic IP WAN SetupDynamic IP Changing WAN Type Static IP Configuration At the Static IP WAN SetupStatic IP Changing WAN Type PPPoE Configuration At the PPPoE WAN SetupPPPoE Chapter Further Configuration PPPoE Parameter Description Changing WAN Type Singapore Adsl Configuration At the Singapore Adsl WAN SetupSingapore Adsl At the Australia BPA WAN Setup Changing WAN Type Pptp Configuration At the Pptp WAN SetupPptp Enabling NAT To set up a De-Militarised Zone host Setting up DMZDisable DMZ To set up port forwarding Set up Port Forwarding For Known Server Address field Set up Port Forwarding For Custom Server Delete a table entry Application Port Number Routing Static Routing Static RoutingSpecify the Destination IP Delete Static Routing By default, Dynamic Routing is disabled Dynamic RoutingDynamic Routing Source IP Address TCP PortTime frame Click on IP Filtering from the Configuration menu IP Filtering At the Destination Port drop down list, select either Further Configuration Filtering Configuration table will then be refreshed Delete IP Filtering Remote Management feature Remote ManagementPort and the Telnet Port Enabling Parallel Broadband Only available in Gateway mode Load balancing Fail-Over Redundancy To enable Parallel Broadband Enable Parallel BroadbandClick on Parallel Broadband from the Configuration menu Using the System Tools Menu System UtilitiesSystem Tools menu System Identity Wlan Station List Wlan Station ListClick on Wlan Station List from the System Tools menu Set System’s Clock Set System’s ClockClick on Set System’s Clock from the System Tools menu Time Zone for the system Firmware Upgrade Firmware UpgradeClick on Firmware Upgrade from the System Tools menu Upgrade Firmware path and file name field Save Your Settings Backup Your SettingsRestore Your Settings Reset Your Settings to Factory Default Reboot System Reboot Your deviceClick on Reboot System from the System Tools menu Change Password Changing your Password Logout Using the Help menu Get Technical Support Get Technical SupportClick on Get Technical Support from the Help menu About System Appendix I Troubleshooting AI Solutions to Common Problems Am not able to access the Web interface of the access point For Netscape 4.7 or later versions Want to set the access point to its factory default settings My laptop is not able to access the AP Appendix I Troubleshooting Operation State Diag LED Appendix III TCP/IP Configuration AIII.1 Configure dynamic IP Address in Windows 98SE/ME 124 Appendix III TCP/IP Configuration Appendix III TCP/IP Configuration AIII.2 Configure dynamic IP Address in Windows XP/2000 Appendix III TCP/IP Configuration AIII.3 Configure static IP Address in Windows 98SE/ME AIII.4 Configure static IP Address in Windows XP/2000 Features Status and Indications Appendix Panel Views and Descriptions Appendix IV Panel Views and Descriptions Appendix Technical Specifications WPA1/2-PSK / WPA1/2-EAP Snmp Appendix V Technical Specifications CE R&TTE Manual Number 0428-V1.4C Version May Cxxxvi