Setup Requirements | Compex Technologies WPE54 guide

Chapter 2 Hardware Installation

Chapter 2 Hardware Installation

2.1Setup Requirements

Before starting, please verify that the following is available: CAT5/5e networking cable

At least one computer is installed with a Web browser and a wired or wireless network interface adapter

TCP/IP protocol is installed and IP address parameters are properly configured on all your network’s nodes

18

Image 19

Compex Technologies WPE54 manual Setup Requirements

Contents

Page Disclaimer Trademark InformationYour Feedback FCC Notice Declaration of Conformity Compex, Inc Technical Support Information Conventions How to Use this DocumentAbout This Document Firmware Chapter Hardware Installation Chapter Further Configuration Appendix Troubleshooting 118 Features and Benefits Hardware Installation Product OverviewIntroduction Hardware Installation STP When to use which mode Access Point Mode Access Point Client Mode Static IP address Gateway ModeDynamic IP address Singapore Adsl Ethernet 512K PPP over Ethernet PPPoEAustralia BPA Cable Wireless Routing Client Mode Wireless Bridge Link Mode Wireless Ethernet Adapter Mode Setup Requirements Hardware Installation Access to the Web interface with uConfig Access to Web-based InterfaceThrough our Utility uConfig Access to Web-based Interface Access to Web-based Interface Direct access to web-based interface via Internet Explorer Access to Web-based Interface Access to Web-based Interface Access to Web-based Interface Setting up your LAN Common ConfigurationManagement Port Setup Management Port Wlan Basic Setup Wlan Security STP Setup Description Parameters Common Configuration View Active Dhcp Leases To view the active Dhcp leasesGo to the Advanced Dhcp Server Reserve Specific IP addresses Common Configuration Delete Dhcp Server Reservation Advanced Wlan SetupBasic Security Basic Setup Wireless Mode To configure the Basic setup of the wireless mode Common Configuration Common Configuration Advanced Setup Wireless Mode To configure the Advanced setup of the wireless modeWlan Advanced Setup AP/Gateway mode only Common Configuration Scan For Site Survey Scan for Site Survey Ssid Link Information table illustrates the following data Show Link InformationShow Link Information Link Information section Features Mode Wireless Extended FeaturesAccess Control The Wireless Pseudo Vlan Wireless Pseudo Vlan Per Node Wireless Pseudo Vlan Per Node Wireless Pseudo Vlan Per Group Wireless Pseudo Vlan Per Group Common Configuration Delete client from a group Tag Vlan Wireless Pseudo Vlan Tag Vlan Common Configuration Delete client from a Tag Vlan Star Configuration WDS Wireless Setup The Wireless Distributed System WDS Chain Configuration WDS WDS Configuration Setup At the Edit WDS Link page which shows Click on the Back button to return to the WDS Status Common Configuration WMM Parameters WMM Parameters WMM Parameters for advanced users Long Distance Parameters Long Distance Parameters available in all modes Distance ACK TimeoutCTS Timeout Outdoor Security Mode is set to Selecting Security ModeWlan Security Security Mode -WEP How to set up WEP Available in ALL modesWhen using 64-bit encryption When using 128-bit encryption At the Wlan Security Setup Further ConfigurationHow to set up WPA-PSK Security Mode -WPA-PSK, WPA2-PSK, WPA-PSK-AUTO Further Configuration Radius Server, if any Security Mode -802.1x/RADIUS Security Mode WPA-EAP, WPA2-EAP, WPA-EAP-AUTO How to set up WPA EAP Further Configuration STP Setup Further Configuration Further Configuration Bandwidth STP Cost Scenario #1 No STP, No Pseudo Vlan Scenario #2 With STP, No Pseudo Vlan Scenario #3 With STP and Pseudo Vlan Hello Time Enabling STP SetupForwarding Delay Priority MAC Filtering Snmp SetupEnabling Snmp Enabling MAC Filtering UConfig Set up Setting up uConfig Click on WAN Setup from the Configuration menu Configuring WAN SetupChanging WAN Type At the Dynamic IP WAN Setup Changing WAN Type Dynamic IP ConfigurationDynamic IP At the Static IP WAN Setup Changing WAN Type Static IP ConfigurationStatic IP At the PPPoE WAN Setup Changing WAN Type PPPoE ConfigurationPPPoE PPPoE Parameter Description Chapter Further Configuration At the Singapore Adsl WAN Setup Changing WAN Type Singapore Adsl ConfigurationSingapore Adsl At the Australia BPA WAN Setup At the Pptp WAN Setup Changing WAN Type Pptp ConfigurationPptp Enabling NAT Setting up DMZ To set up a De-Militarised Zone hostDisable DMZ To set up port forwarding Address field Set up Port Forwarding For Known Server Delete a table entry Set up Port Forwarding For Custom Server Application Port Number Routing Delete Static Routing Static RoutingStatic Routing Specify the Destination IP Dynamic Routing By default, Dynamic Routing is disabledDynamic Routing TCP Port Source IP AddressTime frame IP Filtering Click on IP Filtering from the Configuration menu At the Destination Port drop down list, select either Further Configuration Delete IP Filtering Filtering Configuration table will then be refreshed Remote Management Remote Management featurePort and the Telnet Port Load balancing Enabling Parallel Broadband Only available in Gateway mode Fail-Over Redundancy Enable Parallel Broadband To enable Parallel BroadbandClick on Parallel Broadband from the Configuration menu System Identity Using the System Tools MenuSystem Utilities System Tools menu Wlan Station List Wlan Station ListClick on Wlan Station List from the System Tools menu Time Zone for the system Set System’s ClockSet System’s Clock Click on Set System’s Clock from the System Tools menu Upgrade Firmware path and file name field Firmware UpgradeFirmware Upgrade Click on Firmware Upgrade from the System Tools menu Reset Your Settings to Factory Default Save Your SettingsBackup Your Settings Restore Your Settings Reboot Your device Reboot SystemClick on Reboot System from the System Tools menu Changing your Password Change Password Logout Get Technical Support Using the Help menu Get Technical SupportClick on Get Technical Support from the Help menu About System AI Solutions to Common Problems Appendix I Troubleshooting For Netscape 4.7 or later versions Am not able to access the Web interface of the access point My laptop is not able to access the AP Want to set the access point to its factory default settings Appendix I Troubleshooting Diag LED Operation State AIII.1 Configure dynamic IP Address in Windows 98SE/ME Appendix III TCP/IP Configuration 124 Appendix III TCP/IP Configuration Appendix III TCP/IP Configuration AIII.2 Configure dynamic IP Address in Windows XP/2000 Appendix III TCP/IP Configuration AIII.3 Configure static IP Address in Windows 98SE/ME AIII.4 Configure static IP Address in Windows XP/2000 Appendix Panel Views and Descriptions Features Status and Indications Appendix IV Panel Views and Descriptions WPA1/2-PSK / WPA1/2-EAP Appendix Technical Specifications Snmp CE R&TTE Appendix V Technical Specifications Manual Number 0428-V1.4C Version May Cxxxvi