Wireless Routing Client Mode | Compex Technologies WPE54 specification

Chapter 2 Hardware Installation

1.3.4The Wireless Routing Client Mode

An application of this mode would be for the Ethernet port of the Wireless Routing Client to be used for connection with other devices on the network while access to the Internet would be achieved through wireless communication with wireless ISP.

16

Image 17

Compex Technologies WPE54 manual Wireless Routing Client Mode

Contents

Page Your Feedback Trademark InformationDisclaimer FCC Notice Declaration of Conformity Compex, Inc Technical Support Information About This Document How to Use this DocumentFirmware Conventions Chapter Hardware Installation Chapter Further Configuration Appendix Troubleshooting 118 Introduction Hardware Installation Product OverviewFeatures and Benefits Hardware Installation STP When to use which mode Access Point Mode Access Point Client Mode Dynamic IP address Gateway ModeStatic IP address Australia BPA Cable PPP over Ethernet PPPoESingapore Adsl Ethernet 512K Wireless Routing Client Mode Wireless Bridge Link Mode Wireless Ethernet Adapter Mode Setup Requirements Hardware Installation Through our Utility uConfig Access to Web-based InterfaceAccess to the Web interface with uConfig Access to Web-based Interface Access to Web-based Interface Direct access to web-based interface via Internet Explorer Access to Web-based Interface Access to Web-based Interface Access to Web-based Interface Management Port Setup Common ConfigurationManagement Port Wlan Basic Setup Wlan Security STP Setup Setting up your LAN Description Parameters Common Configuration Go to the Advanced Dhcp Server To view the active Dhcp leasesView Active Dhcp Leases Reserve Specific IP addresses Common Configuration Delete Dhcp Server Reservation Basic Wlan SetupSecurity Advanced Basic Setup Wireless Mode To configure the Basic setup of the wireless mode Common Configuration Common Configuration Wlan Advanced Setup To configure the Advanced setup of the wireless modeAdvanced Setup Wireless Mode AP/Gateway mode only Common Configuration Scan For Site Survey Scan for Site Survey Ssid Show Link Information Show Link InformationLink Information section Link Information table illustrates the following data Access Control The Wireless Pseudo Vlan Wireless Extended FeaturesFeatures Mode Wireless Pseudo Vlan Per Node Wireless Pseudo Vlan Per Node Wireless Pseudo Vlan Per Group Wireless Pseudo Vlan Per Group Common Configuration Delete client from a group Tag Vlan Wireless Pseudo Vlan Tag Vlan Common Configuration Delete client from a Tag Vlan Star Configuration WDS Wireless Setup The Wireless Distributed System WDS Chain Configuration WDS WDS Configuration Setup At the Edit WDS Link page which shows Click on the Back button to return to the WDS Status Common Configuration WMM Parameters WMM Parameters WMM Parameters for advanced users Long Distance Parameters Long Distance Parameters available in all modes CTS Timeout ACK TimeoutOutdoor Distance Wlan Security Selecting Security ModeSecurity Mode is set to When using 64-bit encryption How to set up WEP Available in ALL modesSecurity Mode -WEP When using 128-bit encryption How to set up WPA-PSK Further ConfigurationSecurity Mode -WPA-PSK, WPA2-PSK, WPA-PSK-AUTO At the Wlan Security Setup Further Configuration Radius Server, if any Security Mode -802.1x/RADIUS Security Mode WPA-EAP, WPA2-EAP, WPA-EAP-AUTO How to set up WPA EAP Further Configuration STP Setup Further Configuration Further Configuration Bandwidth STP Cost Scenario #1 No STP, No Pseudo Vlan Scenario #2 With STP, No Pseudo Vlan Scenario #3 With STP and Pseudo Vlan Forwarding Delay Enabling STP SetupPriority Hello Time Enabling Snmp Snmp SetupMAC Filtering Enabling MAC Filtering UConfig Set up Setting up uConfig Changing WAN Type Configuring WAN SetupClick on WAN Setup from the Configuration menu Dynamic IP Changing WAN Type Dynamic IP ConfigurationAt the Dynamic IP WAN Setup Static IP Changing WAN Type Static IP ConfigurationAt the Static IP WAN Setup PPPoE Changing WAN Type PPPoE ConfigurationAt the PPPoE WAN Setup PPPoE Parameter Description Chapter Further Configuration Singapore Adsl Changing WAN Type Singapore Adsl ConfigurationAt the Singapore Adsl WAN Setup At the Australia BPA WAN Setup Pptp Changing WAN Type Pptp ConfigurationAt the Pptp WAN Setup Enabling NAT Disable DMZ To set up a De-Militarised Zone hostSetting up DMZ To set up port forwarding Address field Set up Port Forwarding For Known Server Delete a table entry Set up Port Forwarding For Custom Server Application Port Number Routing Static Routing Static RoutingSpecify the Destination IP Delete Static Routing Dynamic Routing By default, Dynamic Routing is disabledDynamic Routing Time frame Source IP AddressTCP Port IP Filtering Click on IP Filtering from the Configuration menu At the Destination Port drop down list, select either Further Configuration Delete IP Filtering Filtering Configuration table will then be refreshed Port and the Telnet Port Remote Management featureRemote Management Load balancing Enabling Parallel Broadband Only available in Gateway mode Fail-Over Redundancy Click on Parallel Broadband from the Configuration menu To enable Parallel BroadbandEnable Parallel Broadband System Utilities Using the System Tools MenuSystem Tools menu System Identity Click on Wlan Station List from the System Tools menu Wlan Station ListWlan Station List Set System’s Clock Set System’s ClockClick on Set System’s Clock from the System Tools menu Time Zone for the system Firmware Upgrade Firmware UpgradeClick on Firmware Upgrade from the System Tools menu Upgrade Firmware path and file name field Backup Your Settings Save Your SettingsRestore Your Settings Reset Your Settings to Factory Default Click on Reboot System from the System Tools menu Reboot SystemReboot Your device Changing your Password Change Password Logout Click on Get Technical Support from the Help menu Using the Help menu Get Technical SupportGet Technical Support About System AI Solutions to Common Problems Appendix I Troubleshooting For Netscape 4.7 or later versions Am not able to access the Web interface of the access point My laptop is not able to access the AP Want to set the access point to its factory default settings Appendix I Troubleshooting Diag LED Operation State AIII.1 Configure dynamic IP Address in Windows 98SE/ME Appendix III TCP/IP Configuration 124 Appendix III TCP/IP Configuration Appendix III TCP/IP Configuration AIII.2 Configure dynamic IP Address in Windows XP/2000 Appendix III TCP/IP Configuration AIII.3 Configure static IP Address in Windows 98SE/ME AIII.4 Configure static IP Address in Windows XP/2000 Appendix Panel Views and Descriptions Features Status and Indications Appendix IV Panel Views and Descriptions WPA1/2-PSK / WPA1/2-EAP Appendix Technical Specifications Snmp CE R&TTE Appendix V Technical Specifications Manual Number 0428-V1.4C Version May Cxxxvi