Identifying External Components, Front Panel | D-Link DES-3624

Stackable NWay Ethernet Switch User’s Guide

3

IDENTIFYING EXTERNAL COMPONENTS

This chapter describes the front panel, rear panel, optional plug-in modules, and LED indicators of the Switch

Front Panel

The front panel of the Switch consists of either 22 or 20 (10/100 Mbps) Ethernet/Fast Ethernet ports, two or one uplink jacks, a slide-in module slot for 10/100 Mbps Ethernet ports, an RS-232 communication port (DES- 3624i, DES-3624iF, and DES-3624iFM only), and LED indicators.

♦

♦

♦

♦

♦

Figure 3-1. Front panel view of the Switches

Comprehensive LED indicators display the conditions of the Switch and status of the network. A description of these LED indicators follows (see LED Indicators).

An RS-232 DCE console port is used to diagnose the Switch via a connection to a PC and Local Console Management (DES-3624i, DES-3624iF, and DES-3624iFM only).

Twenty or 22 high performance NWay ports all operate at 10/100 Mbps for connection to servers and hubs. All ports can be auto-negotiated between 10Mbps or 100Mbps.

A slide-in module slot (labeled Slot1) for 10/100 Mbps Ethernet ports can accommodate the following modules: 2-port TX, 2-port FX (MT-RJ), or 1-port FX (SC).

One or two MDI-IIuplink jacks are supported. Port numbers 1 and 2 on the DES-3624, DES-3624F, and DES-3624FM are equipped with MDI-Xjacks for normal end-node connections and MDI-IIjacks for uplink connections. Port number 1 on the DES-3624i, DES-3624iF, and DES-3624iFM are equipped with an MDI-Xjack for normal end-node connection and an MDI-IIjack for uplink connection.

Identifying External Components

17

Image 17

D-Link DES-3624 manual Identifying External Components, Front Panel

Contents

DES-3624 Series Stackable NWay Ethernet Switch User’s Guide Wichtige Sicherheitshinweise Warranties Exclusive Hardware Link Offices for Registration and Warranty ServiceSoftware Trademarks FCC Warning Copyright StatementCE Mark Warning Vcci Warning Bsmi Warning Table of Contents Using the Console Interface Technical Specifications Runtime Software Default Settings Overview of this User’s Guide About this GuideConventions Gigabit Ethernet Technology IntroductionFast Ethernet Technology Ports Switching TechnologyFeatures Management Performance features Setup Unpacking and SetupDesktop or Shelf Installation Unpacking Switch installed on a Desktop or Shelf Rack Installation Power Failure Power On Front Panel Identifying External Components Side Panels Rear Panel Stack Operation Side panel views of the Switch Optional Plug-in Modules Switch stack with example of possible connections 100BASE-FX SC Module 100BASE-FX MT-RJ Module 1000BASE-SX Gigabit Module 100BASE-TX Module 1000BASE-T Copper Gigabit Module 1000BASE-LX Gigabit Module 12. The Switch LED indicators LED Indicators Identifying External Components Switch to Hub or Switch Connecting the SwitchSwitch to End Node 100BASE-TX Device 10BASE-T Device Local Console Management Switch Management ConceptsDiagnostic Console Port RS-232 DCE Traps IP Addresses and Snmp Community Names Aging Time MIBsPacket Forwarding Filtering Database Spanning Tree Algorithm User-Changeable STA Parameters STA Operation LevelsOn the Bridge Level On the Port Level Before Applying the STA Rules Illustration of STA Port Trunking STA parameters Settings Effects Comment Bridge Priority Vlan Sharing Resources Across VLANs Ieee 802.1Q VLANsVlan Segmentation Pvid VID VLANs Spanning Multiple Switches Broadcast Management VLANs Over 802.1Q-compliant Switches MAC-based Broadcast Packet Filter Broadcast StormsPort-based Broadcast Packet Filter Setting Up a Console Using the Console Interface Console Usage Conventions Connecting to the Switch Using Telnet Initial Screen, first time connecting to the Switch User Accounts Management Administrator and Normal User Privileges Save Changes Menu Administrator Normal User Privilege Create/Modify User Accounts Login On The Switch Console By Registered Users User Accounts Management menu Add/Modify User Accounts screen View/Delete User Accounts System Configuration Setting Up The Switch System Configuration menu Configure IP Address IP Address Configuration screen Settings on Restart Configure Console 11. Switch Stack Configuration screen Configure Switch Stack 12A. Information of Individual Switch Unit screen Information of Individual Switch Unit 12B. Information of Individual Switch Unit screen Advance Settings 13. Configure Advanced Switch Features screen Configure Port 14. Port Configuration screen Configure Trunk 15. Port Trunk screen Configure Spanning Tree Protocol Configure Port Mirroring 17. Configure Spanning Tree Protocol menu STP Parameter Settings 18. STP Parameter Setting screen STP Custom Settings 19. STP Custom Settings screen Configure Filtering and Forwarding Table 20. Configure Filtering and Forwarding table screen 21. Static Forwarding Table Configuration screen Configure Static Forwarding Table Entry 22. Custom Filtering Table screen Configure MAC Address Filtering Configure Igmp Configure Permanent Multicast Filtering 24. Igmp Configuration screen 25. Ieee 802.1q Igmp Configuration screen 26. Add/Remove Igmp Entry screen 27. Ieee 802.1Q Igmp Configuration screen Configure VLANs & MAC-based Broadcast Domains 28. VLANs & MAC-based Broadcast Domains Configuration screen Configure MAC-Based Broadcast Domains 29. MAC-Based Broadcast Domains Configuration menu 30. Add/Remove MAC-based Broadcast Domains screen 31. Add/Remove MAC-based Broadcast Domain Members screen 32. Add/Remove MAC-based Broadcast Domain Members screen Configure Ieee 802.1Q VLANs 33. Ieee 802.1Q VLANs Configuration menu 34. Ingress Filtering Check screen 35. Default port Vlan assignment screen 36 .1Q Static Vlan Settings screen 37. Browse 802.1Q Vlan Entries screen Update Firmware and Configuration Files 38. Update Firmware and Configuration Files screen System Utilities Special Note Concerning Firmware Updates Ping Test Save Settings to Tftp Server 41. Save Settings to Tftp Server screen Save Switch History to Tftp Server Clear Address Table Community Strings and Trap Stations 43. Snmp Manager Configuration screen Network Monitoring Switch Monitoring Port Utilization Traffic Statistics 46. Port Utilization screen Port Traffic Statistics 47. Port Traffic Statistics screen 48. Port Packet Error Statistics table Port Packet Error Statistics 49. Packet Analysis Statistics table Port Packet Analysis Statistics Browse Address Table 50. Browse Address Table Switch History Browse Igmp Status 51. Switch History screen 52. IP Multicast Information screen Restart System Resetting the SwitchFactory Reset Logout 54. Factory Reset NV-RAM to Default Value screen Introduction WEB-BASED Network ManagementGetting Started Management IP Address Configuration Configure Switch Stack window Switch Web-Based Network Management 103 Advanced Configure Switch Stack Advanced window Information Of Individual Switch Unit window Switch Unit Port Configure Port window Port Trunk window Port Trunk Port Mirroring window Port Mirroring Spanning Tree Protocol STP Parameters Setting Spanning Tree Custom Setting window STP Custom Setting Forwarding and Filtering 10. Configure Forwarding Table And Filtering Table window Static Forwarding Table Click New to access the Static Forwarding Table Edit window 12. Static Forwarding Table---Edit window 13. Static MAC Address Filtering window MAC Address Filtering Table 14. Static MAC Address Filtering---Edit window 15. Static Permanent Multicast Filtering window Permanent Multicast Filtering Igmp 17. Configure Igmp window Igmp Settings 18. Add/Remove Igmp Table window 802.1Q Igmp 19. Add/Remove Igmp Table-Edit window VLANs & MAC-based Broadcast Domains MAC-Based Broadcast Domains 20. Configure Vlan window 21. Add/Remove MAC-based Broadcast Domains window 22. Add/Remove MAC-based Broadcast Domains --- Edit window 23. Add/Remove MAC-based Broadcast Domain Member window Web-Based Network Management 125 Ieee 802.1Q VLANs 25. Default Port Vlan ID window 26. Port Ingress Filtering Check window 27 .1Q Static Vlan Entry window number one 28 .1Q Static Vlan Entry window number two 29. Community Strings and Trap Stations window Community Strings and Trap Stations 30. User Accounts window User Account 31. User Account-Edit window Console 32. Configure Console window Monitoring Switch Overview 34. Port Utilization window Port Utilization 35. Port Traffic Statistics window Port Traffic Statistics 36. Port Error Packet Statistics window Port Error Packet Statistics 138 37. Port Packet Analysis window Port Packet Analysis Statistics 38. Browse Address Table window 39. Browse Igmp Status window 40. Switch History window Maintenance 41. Firmware and Configuration Update window Firmware and Configuration Update 42. Save Settings To Tftp Server window 43. Save Switch History To Tftp Server window 44. Save Changes window Save Changes 45. Factory Reset to Default Value window Factory Reset 46. Restart System window Restart System General Technical Specifications Physical and Environmental Performance Figure B-1. The standard RJ-45 receptacle/connector RJ-45 PIN Specification RJ-45 Connector pin assignment Commands Sample Configuration File # specify default gateway Defaultgateway = Runtime Software Default Settings Blocking Index MDI-II Untagging Offices Registration Card