Manuals / D-Link / Computer Equipment / Switch

D-Link DES-3624 manual Stackable NWay Ethernet Switch User’s Guide, Web-Based Network Management

Models: DES-3624

1 162

Download 162 pages 15.63 Kb

Page 138

Manual background

Stackable NWay Ethernet Switch User’s Guide

♦Fragments The number of packets less than 64 bytes with either bad framing or an invalid CRC. These are normally the result of collisions.

♦Jabber The number of frames with length more than 1536 bytes and with CRC error or misalignment (bad framing).

♦Late Collision Counts collisions that occur at or after the 64th byte (octet) in the frame. This may indicate that delays on your Ethernet are too long, and you have either exceeded the repeater count or cable length specified in the Ethernet standard.

♦MAC Rx Error Counts data errors detectable as 10BASE-TX “symbol errors,” bit patterns with illegal encodings. This may indicate noise on the line.

♦Dropped Frames The number of frames which are dropped by this port since the last Switch reboot.

♦Undersize Frames The number of frames detected that are less than the minimum permitted frame size of 64 bytes and have a good CRC. Undersize frames usually indicate collision fragments, a normal network occurrence.

♦Total Errors The sum of the CRC Error, Oversize Frames, Fragments, Jabber, Late Collision, MAC Rx Error, Dropped Frames, and Undersize Frames counters.

♦Collisions The best estimate of the total number of collisions on this Ethernet segment.

138	Web-Based Network Management

Image 138

D-Link DES-3624 manual Stackable NWay Ethernet Switch User’s Guide, Web-Based Network Management

Contents

DES-3624 Series Stackable NWay Ethernet Switch User’s Guide 6DES3624..02 Printed In Taiwan RECYCLABLESecond Edition April Wichtige Sicherheitshinweise WARRANTIES EXCLUSIVE LIMITATION OF LIABILITYHardware Limited WarrantyD-Link Offices for Registration and Warranty Service SoftwareCE Mark Warning Copyright StatementFCC Warning VCCI Warning BSMI WarningCONNECTING THE SWITCH TABLE OF CONTENTSUNPACKING AND SETUP SWITCH MANAGEMENT CONCEPTSUSING THE CONSOLE INTERFACE SAMPLE CONFIGURATION FILE TECHNICAL SPECIFICATIONSRJ-45 PIN SPECIFICATION WEB-BASED NETWORK MANAGEMENTRUNTIME SOFTWARE DEFAULT SETTINGS INDEXABOUT THIS GUIDE ConventionsOverview of this User’s Guide INTRODUCTION Fast Ethernet TechnologyGigabit Ethernet Technology Switching Technology FeaturesPorts Performance features ManagementDesktop or Shelf Installation UNPACKING AND SETUPSetup UnpackingFigure 2-2A. Attaching the mounting brackets to the Switch Rack InstallationFigure 2-1. Switch installed on a Desktop or Shelf Figure 2-2B. Installing the Switch in an equipment rackPower On Power FailureFigure 3-1. Front panel view of the Switches IDENTIFYING EXTERNAL COMPONENTSFront Panel Figure 3-2. Rear panel view of the Switches Rear PanelSide Panels Figure 3-3. Side panel views of the Switch Figure 3-4. Switch stack with one master and three slavesStack Operation Stackable NWay Ethernet Switch User’s Guide Figure 3-5. Switch stack with example of possible connectionsOptional Plug-in Modules Identifying External ComponentsFigure 3-6. Two-port, 100BASE-FX MT-RJ module 100BASE-FX MT-RJ Module100BASE-FX SC Module Figure 3-7. One-port, 100BASE-FX SC moduleFigure 3-8. Two-port, 100BASE-TX module 100BASE-TX Module1000BASE-SX Gigabit Module Figure 3-9. One-port, 1000BASE-SX gigabit moduleFigure 3-10. One-port, 1000BASE-LX gigabit module 1000BASE-LX Gigabit Module1000BASE-T Copper Gigabit Module Figure 3-11. One-port, 1000BASE-T gigabit moduleLED Indicators Figure 3-12. The Switch LED indicators100M These indicators are illuminated green when a 100 Mbps device is connected to any of the 22+2 or 20+2 ports or uplink port. If a 10 Mbps device is connected to any of the 24 ports or uplink port, these LEDs remain dark. When a port is active, these indicators will blink green Switch to Hub or Switch CONNECTING THE SWITCHSwitch to End Node Figure 4-1. Switch connected to an End Node10BASE-T Device 100BASE-TX DeviceSWITCH MANAGEMENT CONCEPTS Diagnostic Console Port RS-232 DCELocal Console Management IP Addresses and SNMP Community Names TrapsMIBs Packet ForwardingAging Time Spanning Tree Algorithm Filtering DatabaseOn the Bridge Level STA Operation LevelsUser-Changeable STA Parameters On the Port LevelIllustration of STA Figure 5-1. Before Applying the STA RulesPort Trunking Figure 5-2. After Applying the STA RulesTable 5-1. User-selective STA parameters VLAN Figure 5-3. Port trunking exampleVLAN Segmentation Figure 5-4. Example of typical VLAN configurationIEEE 802.1Q VLANs Sharing Resources Across VLANsPVID VLANs Spanning Multiple SwitchesPort PortsVLANs Over 802.1Q-compliant Switches Figure 5-5. Data transmissions between 802.1Q-compliant SwitchesBroadcast Management Broadcast Storms Port-based Broadcast Packet FilterMAC-based Broadcast Packet Filter USING THE CONSOLE INTERFACE Setting Up A ConsoleFigure 6-1. Example of a console connection Connecting to the Switch Using TelnetConsole Usage Conventions First Time Connecting To The SwitchFigure 6-2. Initial Screen, first time connecting to the Switch User Accounts Management Figure 6-3. Main MenuAdministrator and Normal User Privileges Table 6-1. Administrator and Normal User Privileges Save ChangesLogin On The Switch Console By Registered Users Create/Modify User AccountsFigure 6-4. Save Changes screen Using the Console Interface Figure 6-5. User Accounts Management menuStackable NWay Ethernet Switch User’s Guide 2. Choose Create/Modify User Accounts. The following screen appearsView/Delete User Accounts Figure 6-6. Add/Modify User Accounts screenSetting Up The Switch System ConfigurationFigure 6-7. View/Delete User Accounts screen Configure IP Address Figure 6-8. System Configuration menuFigure 6-9. IP Address Configuration screen Configure Console Settings on RestartFigure 6-10. Console Options screen Configure Switch Stack Figure 6-11. Switch Stack Configuration screenInformation of Individual Switch Unit Figure 6-12A. Information of Individual Switch Unit screenAdvance Settings Figure 6-12B. Information of Individual Switch Unit screenConfigure Port Figure 6-13. Configure Advanced Switch Features screenFigure 6-14. Port Configuration screen Configure Trunk Figure 6-15. Port Trunk screen Configure Port Mirroring Configure Spanning Tree ProtocolFigure 6-16. Port Mirroring Configuration screen STP Parameter Settings Figure 6-17. Configure Spanning Tree Protocol menuFigure 6-18. STP Parameter Setting screen STP Custom Settings Configure Filtering and Forwarding Table Figure 6-19. STP Custom Settings screenFigure 6-20. Configure Filtering and Forwarding table screen Configure Static Forwarding Table Entry Figure 6-21. Static Forwarding Table Configuration screenConfigure MAC Address Filtering Figure 6-22. Custom Filtering Table screenConfigure Permanent Multicast Filtering Configure IGMPFigure 6-23. Static Multicast Filtering Table Configuration screen Figure 6-24. IGMP Configuration screen Figure 6-25. IEEE 802.1q IGMP Configuration screen Stackable NWay Ethernet Switch User’s GuideUsing the Console Interface Figure 6-26. Add/Remove IGMP Entry screen Configure VLANs & MAC-based Broadcast Domains Figure 6-27. IEEE 802.1Q IGMP Configuration screenConfigure MAC-Based Broadcast Domains Figure 6-28. VLANs & MAC-based Broadcast Domains Configuration screenFigure 6-29. MAC-Based Broadcast Domains Configuration menu Figure 6-30. Add/Remove MAC-based Broadcast Domains screen Figure 6-31. Add/Remove MAC-based Broadcast Domain Members screen Stackable NWay Ethernet Switch User’s GuideUsing the Console Interface Configure IEEE 802.1Q VLANs Figure 6-32. Add/Remove MAC-based Broadcast Domain Members screenFigure 6-33. IEEE 802.1Q VLANs Configuration menu Figure 6-34. Ingress Filtering Check screen Figure 6-35. Default port VLAN assignment screen Figure 6-36. 802.1Q Static VLAN Settings screen Update Firmware and Configuration Files Figure 6-37. Browse 802.1Q VLAN Entries screenFigure 6-38. Update Firmware and Configuration Files screen Special Note Concerning Firmware Updates System UtilitiesFigure 6-39. Utilities menu Save Settings to TFTP Server Ping TestFigure 6-40. Ping Test screen Save Switch History to TFTP Server Figure 6-41. Save Settings to TFTP Server screenFigure 6-42. Save Switch History to TFTP Server screen Community Strings and Trap StationsClear Address Table Figure 6-43. SNMP Manager Configuration screen Switch Monitoring Network MonitoringFigure 6-44. Network Monitoring menu Traffic Statistics Port UtilizationFigure 6-45. Traffic Statistics menu Port Traffic Statistics Figure 6-46. Port Utilization screenFigure 6-47. Port Traffic Statistics screen Port Packet Error Statistics Figure 6-48. Port Packet Error Statistics tablePort Packet Analysis Statistics Figure 6-49. Packet Analysis Statistics tableBrowse Address Table Switch History Figure 6-50. Browse Address TableFigure 6-51. Switch History screen Browse IGMP StatusFigure 6-52. IP Multicast Information screen Restart System Resetting the SwitchFactory Reset Figure 6-53. Restart System screenFigure 6-54. Factory Reset NV-RAM to Default Value screen LogoutGetting Started WEB-BASED NETWORK MANAGEMENTIntroduction ManagementConfiguration Figure 7-1. Configure IP Address windowIP Address Switch Figure 7-2. Configure Switch Stack windowThe information in the window above is described as follows Figure 7-3. Configure Switch Stack - Advanced window AdvancedSwitch Unit Figure 7-4. Information Of Individual Switch Unit windowFigure 7-5. Configure Port window PortPort Trunk Figure 7-6. Port Trunk windowPort Mirroring Figure 7-7. Port Mirroring windowSTP Parameters Setting Figure 7-8. STP Parameter Setting windowSpanning Tree Protocol STP Custom Setting Figure 7-9. Spanning Tree Custom Setting windowFigure 7-10. Configure Forwarding Table And Filtering Table window Forwarding and FilteringClick New to access the Static Forwarding Table - Edit window Static Forwarding TableFigure 7-11. Static Forwarding Table window Figure 7-12. Static Forwarding Table---Edit window Figure 7-13. Static MAC Address Filtering window Click New to access the Static MAC Address Filtering - Edit windowMAC Address Filtering Table Stackable NWay Ethernet Switch User’s GuideFigure 7-14. Static MAC Address Filtering---Edit window Stackable NWay Ethernet Switch User’s Guide Permanent Multicast FilteringFigure 7-15. Static Permanent Multicast Filtering window Web-Based Network ManagementIGMP Figure 7-16. Static Permanent Multicast Filtering--Edit windowStackable NWay Ethernet Switch User’s Guide IGMP SettingsFigure 7-17. Configure IGMP window Web-Based Network Management802.1Q IGMP Figure 7-18. Add/Remove IGMP Table windowVLANs & MAC-based Broadcast Domains Figure 7-19. Add/Remove IGMP Table-Edit windowFigure 7-20. Configure VLAN window MAC-Based Broadcast DomainsFigure 7-21. Add/Remove MAC-based Broadcast Domains window Description The name of the Broadcast Domain to be added Figure 7-22. Add/Remove MAC-based Broadcast Domains --- Edit windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-23. Add/Remove MAC-based Broadcast Domain Member window Page Stackable NWay Ethernet Switch User’s Guide Figure 7-25. Default Port VLAN ID windowIEEE 802.1Q VLANs Web-Based Network ManagementFigure 7-26. Port Ingress Filtering Check window Stackable NWay Ethernet Switch User’s GuideWeb-Based Network Management Stackable NWay Ethernet Switch User’s Guide Figure 7-27. 802.1Q Static VLAN Entry window number oneClick the pointer icon to access the second 802.1Q VLAN Entry window Web-Based Network ManagementFigure 7-28. 802.1Q Static VLAN Entry window number two ManagementCommunity Strings and Trap Stations Figure 7-29. Community Strings and Trap Stations windowStackable NWay Ethernet Switch User’s Guide User AccountFigure 7-30. User Accounts window Web-Based Network ManagementFigure 7-31. User Account-Edit window Figure 7-32. Configure Console window ConsoleSwitch Overview Figure 7-33. Switch Statistics windowMonitoring Port Utilization Figure 7-34. Port Utilization windowPort Traffic Statistics Figure 7-35. Port Traffic Statistics windowPort Error Packet Statistics Figure 7-36. Port Error Packet Statistics windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementPort Packet Analysis Statistics Figure 7-37. Port Packet Analysis windowFigure 7-38. Browse Address Table window Browse Address TableFigure 7-39. Browse IGMP Status window Browse IGMP StatusMaintenance Figure 7-40. Switch History windowSwitch History Firmware and Configuration Update Figure 7-41. Firmware and Configuration Update windowSave Settings To TFTP Server Figure 7-42. Save Settings To TFTP Server windowSave Switch History To TFTP Server Figure 7-43. Save Switch History To TFTP Server windowStackable NWay Ethernet Switch User’s Guide Save ChangesFigure 7-44. Save Changes window Web-Based Network ManagementStackable NWay Ethernet Switch User’s Guide Factory ResetFigure 7-45. Factory Reset to Default Value window Web-Based Network ManagementStackable NWay Ethernet Switch User’s Guide Restart SystemFigure 7-46. Restart System window Web-Based Network ManagementStackable NWay Ethernet Switch User’s Guide TECHNICAL SPECIFICATIONSGeneral Technical SpecificationsTechnical Specifications Physical and EnvironmentalStackable NWay Ethernet Switch User’s Guide GeneralStackable NWay Ethernet Switch User’s Guide Technical SpecificationsPerformance RJ-45 PIN SPECIFICATION Figure B-1. The standard RJ-45 receptacle/connectorRJ-45 Connector pin assignment Table B-1. The standard Category 3 cable, RJ-45 pin assignmentconnection Notes about the Configuration File SAMPLE CONFIGURATION FILECommands Defaultgateway# Sample Config File Codetype=PROM Imagefile=e\3624\3624prom.tfp # specify IP address Ipaddr = # specify subnet mask Subnetmask =# specify default gateway Defaultgateway = RUNTIME SOFTWARE DEFAULT SETTINGS Stackable NWay Ethernet Switch User’s GuideINDEX Forward Delay, 34 Forwarding, 57 Front Panel untagging taggingOffices Product Model Registration CardProduct was purchased from Product Serial No