Manuals / D-Link / Computer Equipment / Switch

D-Link DES-3624 manual Port Packet Analysis Statistics, 49. Packet Analysis Statistics table

Models: DES-3624

1 162

Download 162 pages 15.63 Kb

Page 93

Port Packet Analysis Statistics

Stackable NWay Ethernet Switch User’s Guide

♦Mac Rx Error The number of frames with received MAC Errors.

♦Dropped Frames The number of frames which are dropped by this port since the last Switch reboot.

♦Undersize Frames The number of frames detected that are less than the minimum permitted frame size of 64 bytes and have a good CRC. Undersize frames usually indicate collision fragments, a normal network occurrence.

♦Total errors The sum of the CRC Error, Oversize, Bad Fragment, Jabber, Late Collision, Mac Rx Error, Dropped Frames, and Undersize Frames counters.

♦Collisions The number of times packets have collided on this port.

Port Packet Analysis Statistics

To access the fourth item on the Traffic Statistics menu, choose Port Packet Analysis Statistics. The following table appears:

Figure 6-49. Packet Analysis Statistics table

Select the desired device in the Switch field, the desired port in the Port field, and the desired increment setting in the Update Interval field: 5 sec, 15 sec, 30 sec, 1 min, or Suspend.

The statistic counters displayed are defined as follows:

♦64, 65-127, 128-255, 256-511, 512-1023, 1024-1536The number of good frames of various length ranges, both valid and invalid.

Using the Console Interface

93

Image 93

D-Link DES-3624 manual Port Packet Analysis Statistics, 49. Packet Analysis Statistics table

Contents

DES-3624 Series Stackable NWay Ethernet Switch User’s Guide 6DES3624..02 Printed In Taiwan RECYCLABLESecond Edition April Wichtige Sicherheitshinweise LIMITATION OF LIABILITY WARRANTIES EXCLUSIVED-Link Offices for Registration and Warranty Service Limited WarrantyHardware SoftwareFCC Warning Copyright StatementCE Mark Warning VCCI Warning BSMI WarningUNPACKING AND SETUP TABLE OF CONTENTSCONNECTING THE SWITCH SWITCH MANAGEMENT CONCEPTSUSING THE CONSOLE INTERFACE RJ-45 PIN SPECIFICATION TECHNICAL SPECIFICATIONSSAMPLE CONFIGURATION FILE WEB-BASED NETWORK MANAGEMENTINDEX RUNTIME SOFTWARE DEFAULT SETTINGSABOUT THIS GUIDE ConventionsOverview of this User’s Guide INTRODUCTION Fast Ethernet TechnologyGigabit Ethernet Technology Switching Technology FeaturesPorts Management Performance featuresSetup UNPACKING AND SETUPDesktop or Shelf Installation UnpackingFigure 2-1. Switch installed on a Desktop or Shelf Rack InstallationFigure 2-2A. Attaching the mounting brackets to the Switch Figure 2-2B. Installing the Switch in an equipment rackPower Failure Power OnFigure 3-1. Front panel view of the Switches IDENTIFYING EXTERNAL COMPONENTSFront Panel Figure 3-2. Rear panel view of the Switches Rear PanelSide Panels Figure 3-3. Side panel views of the Switch Figure 3-4. Switch stack with one master and three slavesStack Operation Optional Plug-in Modules Figure 3-5. Switch stack with example of possible connectionsStackable NWay Ethernet Switch User’s Guide Identifying External Components100BASE-FX SC Module 100BASE-FX MT-RJ ModuleFigure 3-6. Two-port, 100BASE-FX MT-RJ module Figure 3-7. One-port, 100BASE-FX SC module1000BASE-SX Gigabit Module 100BASE-TX ModuleFigure 3-8. Two-port, 100BASE-TX module Figure 3-9. One-port, 1000BASE-SX gigabit module1000BASE-T Copper Gigabit Module 1000BASE-LX Gigabit ModuleFigure 3-10. One-port, 1000BASE-LX gigabit module Figure 3-11. One-port, 1000BASE-T gigabit moduleFigure 3-12. The Switch LED indicators LED Indicators100M These indicators are illuminated green when a 100 Mbps device is connected to any of the 22+2 or 20+2 ports or uplink port. If a 10 Mbps device is connected to any of the 24 ports or uplink port, these LEDs remain dark. When a port is active, these indicators will blink green Switch to End Node CONNECTING THE SWITCHSwitch to Hub or Switch Figure 4-1. Switch connected to an End Node100BASE-TX Device 10BASE-T DeviceSWITCH MANAGEMENT CONCEPTS Diagnostic Console Port RS-232 DCELocal Console Management Traps IP Addresses and SNMP Community NamesMIBs Packet ForwardingAging Time Filtering Database Spanning Tree AlgorithmUser-Changeable STA Parameters STA Operation LevelsOn the Bridge Level On the Port LevelFigure 5-1. Before Applying the STA Rules Illustration of STAPort Trunking Figure 5-2. After Applying the STA RulesTable 5-1. User-selective STA parameters Figure 5-3. Port trunking example VLANIEEE 802.1Q VLANs Figure 5-4. Example of typical VLAN configurationVLAN Segmentation Sharing Resources Across VLANsPort VLANs Spanning Multiple SwitchesPVID PortsVLANs Over 802.1Q-compliant Switches Figure 5-5. Data transmissions between 802.1Q-compliant SwitchesBroadcast Management Broadcast Storms Port-based Broadcast Packet FilterMAC-based Broadcast Packet Filter Setting Up A Console USING THE CONSOLE INTERFACEConsole Usage Conventions Connecting to the Switch Using TelnetFigure 6-1. Example of a console connection First Time Connecting To The SwitchFigure 6-2. Initial Screen, first time connecting to the Switch User Accounts Management Figure 6-3. Main MenuAdministrator and Normal User Privileges Save Changes Table 6-1. Administrator and Normal User PrivilegesLogin On The Switch Console By Registered Users Create/Modify User AccountsFigure 6-4. Save Changes screen Stackable NWay Ethernet Switch User’s Guide Figure 6-5. User Accounts Management menuUsing the Console Interface 2. Choose Create/Modify User Accounts. The following screen appearsFigure 6-6. Add/Modify User Accounts screen View/Delete User AccountsSetting Up The Switch System ConfigurationFigure 6-7. View/Delete User Accounts screen Figure 6-8. System Configuration menu Configure IP AddressFigure 6-9. IP Address Configuration screen Configure Console Settings on RestartFigure 6-10. Console Options screen Figure 6-11. Switch Stack Configuration screen Configure Switch StackFigure 6-12A. Information of Individual Switch Unit screen Information of Individual Switch UnitFigure 6-12B. Information of Individual Switch Unit screen Advance SettingsFigure 6-13. Configure Advanced Switch Features screen Configure PortFigure 6-14. Port Configuration screen Configure Trunk Figure 6-15. Port Trunk screen Configure Port Mirroring Configure Spanning Tree ProtocolFigure 6-16. Port Mirroring Configuration screen Figure 6-17. Configure Spanning Tree Protocol menu STP Parameter SettingsFigure 6-18. STP Parameter Setting screen STP Custom Settings Figure 6-19. STP Custom Settings screen Configure Filtering and Forwarding TableFigure 6-20. Configure Filtering and Forwarding table screen Figure 6-21. Static Forwarding Table Configuration screen Configure Static Forwarding Table EntryFigure 6-22. Custom Filtering Table screen Configure MAC Address FilteringConfigure Permanent Multicast Filtering Configure IGMPFigure 6-23. Static Multicast Filtering Table Configuration screen Figure 6-24. IGMP Configuration screen Figure 6-25. IEEE 802.1q IGMP Configuration screen Stackable NWay Ethernet Switch User’s GuideUsing the Console Interface Figure 6-26. Add/Remove IGMP Entry screen Figure 6-27. IEEE 802.1Q IGMP Configuration screen Configure VLANs & MAC-based Broadcast DomainsFigure 6-28. VLANs & MAC-based Broadcast Domains Configuration screen Configure MAC-Based Broadcast DomainsFigure 6-29. MAC-Based Broadcast Domains Configuration menu Figure 6-30. Add/Remove MAC-based Broadcast Domains screen Figure 6-31. Add/Remove MAC-based Broadcast Domain Members screen Stackable NWay Ethernet Switch User’s GuideUsing the Console Interface Figure 6-32. Add/Remove MAC-based Broadcast Domain Members screen Configure IEEE 802.1Q VLANsFigure 6-33. IEEE 802.1Q VLANs Configuration menu Figure 6-34. Ingress Filtering Check screen Figure 6-35. Default port VLAN assignment screen Figure 6-36. 802.1Q Static VLAN Settings screen Figure 6-37. Browse 802.1Q VLAN Entries screen Update Firmware and Configuration FilesFigure 6-38. Update Firmware and Configuration Files screen Special Note Concerning Firmware Updates System UtilitiesFigure 6-39. Utilities menu Save Settings to TFTP Server Ping TestFigure 6-40. Ping Test screen Figure 6-41. Save Settings to TFTP Server screen Save Switch History to TFTP ServerFigure 6-42. Save Switch History to TFTP Server screen Community Strings and Trap StationsClear Address Table Figure 6-43. SNMP Manager Configuration screen Switch Monitoring Network MonitoringFigure 6-44. Network Monitoring menu Traffic Statistics Port UtilizationFigure 6-45. Traffic Statistics menu Figure 6-46. Port Utilization screen Port Traffic StatisticsFigure 6-47. Port Traffic Statistics screen Figure 6-48. Port Packet Error Statistics table Port Packet Error StatisticsFigure 6-49. Packet Analysis Statistics table Port Packet Analysis StatisticsBrowse Address Table Figure 6-50. Browse Address Table Switch HistoryBrowse IGMP Status Figure 6-51. Switch History screenFigure 6-52. IP Multicast Information screen Factory Reset Resetting the SwitchRestart System Figure 6-53. Restart System screenLogout Figure 6-54. Factory Reset NV-RAM to Default Value screenIntroduction WEB-BASED NETWORK MANAGEMENTGetting Started ManagementConfiguration Figure 7-1. Configure IP Address windowIP Address Figure 7-2. Configure Switch Stack window SwitchThe information in the window above is described as follows Advanced Figure 7-3. Configure Switch Stack - Advanced windowFigure 7-4. Information Of Individual Switch Unit window Switch UnitPort Figure 7-5. Configure Port windowFigure 7-6. Port Trunk window Port TrunkFigure 7-7. Port Mirroring window Port MirroringSTP Parameters Setting Figure 7-8. STP Parameter Setting windowSpanning Tree Protocol Figure 7-9. Spanning Tree Custom Setting window STP Custom SettingForwarding and Filtering Figure 7-10. Configure Forwarding Table And Filtering Table windowClick New to access the Static Forwarding Table - Edit window Static Forwarding TableFigure 7-11. Static Forwarding Table window Figure 7-12. Static Forwarding Table---Edit window MAC Address Filtering Table Click New to access the Static MAC Address Filtering - Edit windowFigure 7-13. Static MAC Address Filtering window Stackable NWay Ethernet Switch User’s GuideFigure 7-14. Static MAC Address Filtering---Edit window Figure 7-15. Static Permanent Multicast Filtering window Permanent Multicast FilteringStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-16. Static Permanent Multicast Filtering--Edit window IGMPFigure 7-17. Configure IGMP window IGMP SettingsStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-18. Add/Remove IGMP Table window 802.1Q IGMPFigure 7-19. Add/Remove IGMP Table-Edit window VLANs & MAC-based Broadcast DomainsMAC-Based Broadcast Domains Figure 7-20. Configure VLAN windowFigure 7-21. Add/Remove MAC-based Broadcast Domains window Stackable NWay Ethernet Switch User’s Guide Figure 7-22. Add/Remove MAC-based Broadcast Domains --- Edit windowDescription The name of the Broadcast Domain to be added Web-Based Network ManagementFigure 7-23. Add/Remove MAC-based Broadcast Domain Member window Page IEEE 802.1Q VLANs Figure 7-25. Default Port VLAN ID windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-26. Port Ingress Filtering Check window Stackable NWay Ethernet Switch User’s GuideWeb-Based Network Management Click the pointer icon to access the second 802.1Q VLAN Entry window Figure 7-27. 802.1Q Static VLAN Entry window number oneStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementManagement Figure 7-28. 802.1Q Static VLAN Entry window number twoFigure 7-29. Community Strings and Trap Stations window Community Strings and Trap StationsFigure 7-30. User Accounts window User AccountStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-31. User Account-Edit window Console Figure 7-32. Configure Console windowSwitch Overview Figure 7-33. Switch Statistics windowMonitoring Figure 7-34. Port Utilization window Port UtilizationFigure 7-35. Port Traffic Statistics window Port Traffic StatisticsFigure 7-36. Port Error Packet Statistics window Port Error Packet StatisticsWeb-Based Network Management Stackable NWay Ethernet Switch User’s GuideFigure 7-37. Port Packet Analysis window Port Packet Analysis StatisticsBrowse Address Table Figure 7-38. Browse Address Table windowBrowse IGMP Status Figure 7-39. Browse IGMP Status windowMaintenance Figure 7-40. Switch History windowSwitch History Figure 7-41. Firmware and Configuration Update window Firmware and Configuration UpdateFigure 7-42. Save Settings To TFTP Server window Save Settings To TFTP ServerFigure 7-43. Save Switch History To TFTP Server window Save Switch History To TFTP ServerFigure 7-44. Save Changes window Save ChangesStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-45. Factory Reset to Default Value window Factory ResetStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-46. Restart System window Restart SystemStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementGeneral TECHNICAL SPECIFICATIONSStackable NWay Ethernet Switch User’s Guide Technical SpecificationsStackable NWay Ethernet Switch User’s Guide Physical and EnvironmentalTechnical Specifications GeneralStackable NWay Ethernet Switch User’s Guide Technical SpecificationsPerformance Figure B-1. The standard RJ-45 receptacle/connector RJ-45 PIN SPECIFICATIONRJ-45 Connector pin assignment Table B-1. The standard Category 3 cable, RJ-45 pin assignmentconnection Commands SAMPLE CONFIGURATION FILENotes about the Configuration File Defaultgateway# Sample Config File Codetype=PROM Imagefile=e\3624\3624prom.tfp # specify IP address Ipaddr = # specify subnet mask Subnetmask =# specify default gateway Defaultgateway = Stackable NWay Ethernet Switch User’s Guide RUNTIME SOFTWARE DEFAULT SETTINGSINDEX Forward Delay, 34 Forwarding, 57 Front Panel tagging untaggingOffices Product was purchased from Registration CardProduct Model Product Serial No