Manuals / D-Link / Computer Equipment / Switch

D-Link DES-3624 manual Configure IEEE 802.1Q VLANs

Models: DES-3624

1 162

Download 162 pages 15.63 Kb

Page 76

Figure 6-32. Add/Remove MAC-based Broadcast Domain Members screen

Stackable NWay Ethernet Switch User’s Guide

Figure 6-32. Add/Remove MAC-based Broadcast Domain Members screen

The fields you can set are:

♦Action Select the desired action by toggling between Add and Remove.

♦MAC Address The MAC address of the broadcast domain member being added or removed.

Please note that the Status field for the MAC address you have entered may read Not-Apply. Once the Switch is restarted in MAC-based broadcast domain mode, the MAC-addresses will be applied, meaning that the broadcast domain is active.

Current Broadcast Domain, Number of members, MAC Address (in the lower part of the screen), and Status reflect the current conditions. They are read-only fields and cannot be changed.

Configure IEEE 802.1Q VLANs

To configure an IEEE 802.1Q port-based VLAN, you must do three things:

1.Decide if you want to enable Ingress Filtering and enable it on the chosen ports. Ingress filtering applied on a port causes the port to examine all incoming packets and check whether the port itself is a member of the VLAN. This is normally used to keep untagged frames off the Switch, although it can have other uses as well. This setting is configurable for each port in the Ingress Filtering Check screen.

76	Using the Console Interface

Image 76

D-Link DES-3624 manual Configure IEEE 802.1Q VLANs, 32. Add/Remove MAC-based Broadcast Domain Members screen

Contents

6DES3624..02 Printed In Taiwan RECYCLABLE DES-3624 Series Stackable NWay Ethernet Switch User’s GuideSecond Edition April Wichtige Sicherheitshinweise WARRANTIES EXCLUSIVE LIMITATION OF LIABILITYLimited Warranty D-Link Offices for Registration and Warranty ServiceHardware SoftwareCopyright Statement FCC WarningCE Mark Warning VCCI Warning BSMI WarningTABLE OF CONTENTS UNPACKING AND SETUPCONNECTING THE SWITCH SWITCH MANAGEMENT CONCEPTSUSING THE CONSOLE INTERFACE TECHNICAL SPECIFICATIONS RJ-45 PIN SPECIFICATIONSAMPLE CONFIGURATION FILE WEB-BASED NETWORK MANAGEMENTRUNTIME SOFTWARE DEFAULT SETTINGS INDEXConventions ABOUT THIS GUIDEOverview of this User’s Guide Fast Ethernet Technology INTRODUCTIONGigabit Ethernet Technology Features Switching TechnologyPorts Performance features ManagementUNPACKING AND SETUP SetupDesktop or Shelf Installation UnpackingRack Installation Figure 2-1. Switch installed on a Desktop or ShelfFigure 2-2A. Attaching the mounting brackets to the Switch Figure 2-2B. Installing the Switch in an equipment rackPower On Power FailureIDENTIFYING EXTERNAL COMPONENTS Figure 3-1. Front panel view of the SwitchesFront Panel Rear Panel Figure 3-2. Rear panel view of the SwitchesSide Panels Figure 3-4. Switch stack with one master and three slaves Figure 3-3. Side panel views of the SwitchStack Operation Figure 3-5. Switch stack with example of possible connections Optional Plug-in ModulesStackable NWay Ethernet Switch User’s Guide Identifying External Components100BASE-FX MT-RJ Module 100BASE-FX SC ModuleFigure 3-6. Two-port, 100BASE-FX MT-RJ module Figure 3-7. One-port, 100BASE-FX SC module100BASE-TX Module 1000BASE-SX Gigabit ModuleFigure 3-8. Two-port, 100BASE-TX module Figure 3-9. One-port, 1000BASE-SX gigabit module1000BASE-LX Gigabit Module 1000BASE-T Copper Gigabit ModuleFigure 3-10. One-port, 1000BASE-LX gigabit module Figure 3-11. One-port, 1000BASE-T gigabit moduleLED Indicators Figure 3-12. The Switch LED indicators100M These indicators are illuminated green when a 100 Mbps device is connected to any of the 22+2 or 20+2 ports or uplink port. If a 10 Mbps device is connected to any of the 24 ports or uplink port, these LEDs remain dark. When a port is active, these indicators will blink green CONNECTING THE SWITCH Switch to End NodeSwitch to Hub or Switch Figure 4-1. Switch connected to an End Node10BASE-T Device 100BASE-TX DeviceDiagnostic Console Port RS-232 DCE SWITCH MANAGEMENT CONCEPTSLocal Console Management IP Addresses and SNMP Community Names TrapsPacket Forwarding MIBsAging Time Spanning Tree Algorithm Filtering DatabaseSTA Operation Levels User-Changeable STA ParametersOn the Bridge Level On the Port LevelIllustration of STA Figure 5-1. Before Applying the STA RulesFigure 5-2. After Applying the STA Rules Port TrunkingTable 5-1. User-selective STA parameters VLAN Figure 5-3. Port trunking exampleFigure 5-4. Example of typical VLAN configuration IEEE 802.1Q VLANsVLAN Segmentation Sharing Resources Across VLANsVLANs Spanning Multiple Switches PortPVID PortsFigure 5-5. Data transmissions between 802.1Q-compliant Switches VLANs Over 802.1Q-compliant SwitchesBroadcast Management Port-based Broadcast Packet Filter Broadcast StormsMAC-based Broadcast Packet Filter USING THE CONSOLE INTERFACE Setting Up A ConsoleConnecting to the Switch Using Telnet Console Usage ConventionsFigure 6-1. Example of a console connection First Time Connecting To The SwitchFigure 6-2. Initial Screen, first time connecting to the Switch Figure 6-3. Main Menu User Accounts ManagementAdministrator and Normal User Privileges Table 6-1. Administrator and Normal User Privileges Save ChangesCreate/Modify User Accounts Login On The Switch Console By Registered UsersFigure 6-4. Save Changes screen Figure 6-5. User Accounts Management menu Stackable NWay Ethernet Switch User’s GuideUsing the Console Interface 2. Choose Create/Modify User Accounts. The following screen appearsView/Delete User Accounts Figure 6-6. Add/Modify User Accounts screenSystem Configuration Setting Up The SwitchFigure 6-7. View/Delete User Accounts screen Configure IP Address Figure 6-8. System Configuration menuFigure 6-9. IP Address Configuration screen Settings on Restart Configure ConsoleFigure 6-10. Console Options screen Configure Switch Stack Figure 6-11. Switch Stack Configuration screenInformation of Individual Switch Unit Figure 6-12A. Information of Individual Switch Unit screenAdvance Settings Figure 6-12B. Information of Individual Switch Unit screenConfigure Port Figure 6-13. Configure Advanced Switch Features screenFigure 6-14. Port Configuration screen Configure Trunk Figure 6-15. Port Trunk screen Configure Spanning Tree Protocol Configure Port MirroringFigure 6-16. Port Mirroring Configuration screen STP Parameter Settings Figure 6-17. Configure Spanning Tree Protocol menuFigure 6-18. STP Parameter Setting screen STP Custom Settings Configure Filtering and Forwarding Table Figure 6-19. STP Custom Settings screenFigure 6-20. Configure Filtering and Forwarding table screen Configure Static Forwarding Table Entry Figure 6-21. Static Forwarding Table Configuration screenConfigure MAC Address Filtering Figure 6-22. Custom Filtering Table screenConfigure IGMP Configure Permanent Multicast FilteringFigure 6-23. Static Multicast Filtering Table Configuration screen Figure 6-24. IGMP Configuration screen Stackable NWay Ethernet Switch User’s Guide Figure 6-25. IEEE 802.1q IGMP Configuration screenUsing the Console Interface Figure 6-26. Add/Remove IGMP Entry screen Configure VLANs & MAC-based Broadcast Domains Figure 6-27. IEEE 802.1Q IGMP Configuration screenConfigure MAC-Based Broadcast Domains Figure 6-28. VLANs & MAC-based Broadcast Domains Configuration screenFigure 6-29. MAC-Based Broadcast Domains Configuration menu Figure 6-30. Add/Remove MAC-based Broadcast Domains screen Stackable NWay Ethernet Switch User’s Guide Figure 6-31. Add/Remove MAC-based Broadcast Domain Members screenUsing the Console Interface Configure IEEE 802.1Q VLANs Figure 6-32. Add/Remove MAC-based Broadcast Domain Members screenFigure 6-33. IEEE 802.1Q VLANs Configuration menu Figure 6-34. Ingress Filtering Check screen Figure 6-35. Default port VLAN assignment screen Figure 6-36. 802.1Q Static VLAN Settings screen Update Firmware and Configuration Files Figure 6-37. Browse 802.1Q VLAN Entries screenFigure 6-38. Update Firmware and Configuration Files screen System Utilities Special Note Concerning Firmware UpdatesFigure 6-39. Utilities menu Ping Test Save Settings to TFTP ServerFigure 6-40. Ping Test screen Save Switch History to TFTP Server Figure 6-41. Save Settings to TFTP Server screenCommunity Strings and Trap Stations Figure 6-42. Save Switch History to TFTP Server screenClear Address Table Figure 6-43. SNMP Manager Configuration screen Network Monitoring Switch MonitoringFigure 6-44. Network Monitoring menu Port Utilization Traffic StatisticsFigure 6-45. Traffic Statistics menu Port Traffic Statistics Figure 6-46. Port Utilization screenFigure 6-47. Port Traffic Statistics screen Port Packet Error Statistics Figure 6-48. Port Packet Error Statistics tablePort Packet Analysis Statistics Figure 6-49. Packet Analysis Statistics tableBrowse Address Table Switch History Figure 6-50. Browse Address TableFigure 6-51. Switch History screen Browse IGMP StatusFigure 6-52. IP Multicast Information screen Resetting the Switch Factory ResetRestart System Figure 6-53. Restart System screenFigure 6-54. Factory Reset NV-RAM to Default Value screen LogoutWEB-BASED NETWORK MANAGEMENT IntroductionGetting Started ManagementFigure 7-1. Configure IP Address window ConfigurationIP Address Switch Figure 7-2. Configure Switch Stack windowThe information in the window above is described as follows Figure 7-3. Configure Switch Stack - Advanced window AdvancedSwitch Unit Figure 7-4. Information Of Individual Switch Unit windowFigure 7-5. Configure Port window PortPort Trunk Figure 7-6. Port Trunk windowPort Mirroring Figure 7-7. Port Mirroring windowFigure 7-8. STP Parameter Setting window STP Parameters SettingSpanning Tree Protocol STP Custom Setting Figure 7-9. Spanning Tree Custom Setting windowFigure 7-10. Configure Forwarding Table And Filtering Table window Forwarding and FilteringStatic Forwarding Table Click New to access the Static Forwarding Table - Edit windowFigure 7-11. Static Forwarding Table window Figure 7-12. Static Forwarding Table---Edit window Click New to access the Static MAC Address Filtering - Edit window MAC Address Filtering TableFigure 7-13. Static MAC Address Filtering window Stackable NWay Ethernet Switch User’s GuideFigure 7-14. Static MAC Address Filtering---Edit window Permanent Multicast Filtering Figure 7-15. Static Permanent Multicast Filtering windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementIGMP Figure 7-16. Static Permanent Multicast Filtering--Edit windowIGMP Settings Figure 7-17. Configure IGMP windowStackable NWay Ethernet Switch User’s Guide Web-Based Network Management802.1Q IGMP Figure 7-18. Add/Remove IGMP Table windowVLANs & MAC-based Broadcast Domains Figure 7-19. Add/Remove IGMP Table-Edit windowFigure 7-20. Configure VLAN window MAC-Based Broadcast DomainsFigure 7-21. Add/Remove MAC-based Broadcast Domains window Figure 7-22. Add/Remove MAC-based Broadcast Domains --- Edit window Stackable NWay Ethernet Switch User’s GuideDescription The name of the Broadcast Domain to be added Web-Based Network ManagementFigure 7-23. Add/Remove MAC-based Broadcast Domain Member window Page Figure 7-25. Default Port VLAN ID window IEEE 802.1Q VLANsStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementStackable NWay Ethernet Switch User’s Guide Figure 7-26. Port Ingress Filtering Check windowWeb-Based Network Management Figure 7-27. 802.1Q Static VLAN Entry window number one Click the pointer icon to access the second 802.1Q VLAN Entry windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-28. 802.1Q Static VLAN Entry window number two ManagementCommunity Strings and Trap Stations Figure 7-29. Community Strings and Trap Stations windowUser Account Figure 7-30. User Accounts windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFigure 7-31. User Account-Edit window Figure 7-32. Configure Console window ConsoleFigure 7-33. Switch Statistics window Switch OverviewMonitoring Port Utilization Figure 7-34. Port Utilization windowPort Traffic Statistics Figure 7-35. Port Traffic Statistics windowPort Error Packet Statistics Figure 7-36. Port Error Packet Statistics windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementPort Packet Analysis Statistics Figure 7-37. Port Packet Analysis windowFigure 7-38. Browse Address Table window Browse Address TableFigure 7-39. Browse IGMP Status window Browse IGMP StatusFigure 7-40. Switch History window MaintenanceSwitch History Firmware and Configuration Update Figure 7-41. Firmware and Configuration Update windowSave Settings To TFTP Server Figure 7-42. Save Settings To TFTP Server windowSave Switch History To TFTP Server Figure 7-43. Save Switch History To TFTP Server windowSave Changes Figure 7-44. Save Changes windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementFactory Reset Figure 7-45. Factory Reset to Default Value windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementRestart System Figure 7-46. Restart System windowStackable NWay Ethernet Switch User’s Guide Web-Based Network ManagementTECHNICAL SPECIFICATIONS GeneralStackable NWay Ethernet Switch User’s Guide Technical SpecificationsPhysical and Environmental Stackable NWay Ethernet Switch User’s GuideTechnical Specifications GeneralTechnical Specifications Stackable NWay Ethernet Switch User’s GuidePerformance RJ-45 PIN SPECIFICATION Figure B-1. The standard RJ-45 receptacle/connectorTable B-1. The standard Category 3 cable, RJ-45 pin assignment RJ-45 Connector pin assignmentconnection SAMPLE CONFIGURATION FILE CommandsNotes about the Configuration File Defaultgateway# specify IP address Ipaddr = # specify subnet mask Subnetmask = # Sample Config File Codetype=PROM Imagefile=e\3624\3624prom.tfp# specify default gateway Defaultgateway = RUNTIME SOFTWARE DEFAULT SETTINGS Stackable NWay Ethernet Switch User’s GuideINDEX Forward Delay, 34 Forwarding, 57 Front Panel untagging taggingOffices Registration Card Product was purchased fromProduct Model Product Serial No